- 您現在的位置：買賣IC網 > Datasheet目錄43 > MAX5922AEUI+ (Maxim Integrated)IC NETWORK PWR SW +48V 28-TSSOP Datasheet資料下載
參數資料
| 型號： | MAX5922AEUI+ |
| 廠商： | Maxim Integrated |
| 文件頁數： | 15/21頁 |
| 文件大小： | 437K |
| 描述： | IC NETWORK PWR SW +48V 28-TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 類型： | 以太網供電開關（PoE） |
| 應用： | 遠程外設（工業控制，相機，數據訪問） |
| 內部開關： | 是 |
| 電源電壓： | 32 V ~ 60 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 28-TSSOP |
| 包裝： | 管件 |
| 產品目錄頁面： | 1411 (CN2011-ZH PDF) |
+48V, Single-Port Network Power Switch
For Power-Over-LAN
______________________________________________________________________________________ 15
PD Classification Mode
(PD Classification)
Following a valid PD detection, and if the CLASS pin is
high, the MAX5922 enters the PD classification mode. If
the CLASS pin is low, the PD classification mode is
skipped and the MAX5922 goes directly from PD
detection to the power mode. During the PD classifica-
tion mode, the MAX5922 forces a probe voltage (17.5V)
at the OUT pin and measures the current out of this pin.
The measured current determines the class of the PD.
The classification results are reported at the classifica-
tion logic outputs CL0, CL1, CL2. Table 2 shows the
classification threshold limits and the corresponding
logic outputs CL0, CL1, and CL2.
Connect an external 150& ?% resistor (R
RCL
) from
RCL to IN to set the classification current reference. If
the PD classification function is not used, RCL can be
left floating. For the MAX5922B/MAX5922C, the
DET_DIS pin must be connected low to enable the
classification phase. If DET_DIS is connected high, the
classification phase is disabled regardless of the state
of the CLASS pin. After the classification phase, the
MAX5922 enters power-up.
Power-Up Mode
After the PD is successfully detected and classified, the
MAX5922 enters power-up mode. During this mode,
the MAX5922 gradually turns on the integrated N-chan-
nel MOSFET. To minimize EMI, the MAX5922 limits the
Table 2. PD Classification Threshold Limits
SENSED CURRENT (mA)
CL2
CL1
CL0
CLASS TYPES
0.5 to 4 or above 43
0
0
0
Class 0
9 to 12
0
0
1
Class 1
17 to 20
0
1
0
Class 2
26 to 30
0
1
1
Class 3
36 to 42
1
0
0
Class 4
N/A
1
0
1
Not used
N/A
1
1
0
Successful detection (classification disabled or DET_DIS = low)
Power device not detected yet
or CLASS pin connected low.
1
1
1
Detection ongoing
t
0V
t
DET1
=
88ms
t
DET2
=
88ms
UVLO
8V
4V
V
IN
V
OUT
Figure 5. PD Detection with an Invalid PD Signature
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5923EUP+T | IC HOT-SWAP SWITCH +60V 20-TSSOP |
| MAX5926EEE+ | IC HOT-SWAP CONTROLLER 16QSOP-EP |
| MAX5929BEEG+ | IC HOT SWAP CTLR QUAD 24QSOP |
| MAX5930AEEG+ | IC HOT SWAP CTLR PWR SEQ 24QSOP |
| MAX5932ESA+T | IC HOT-SWAP CONTROLLER 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5922AEUI+ | 功能描述:熱插拔功率分布 48V Single-Port Network Power Switch RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5922AEUI+T | 功能描述:熱插拔功率分布 48V Single-Port Network Power Switch RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5922AEUI-T | 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5922BEUI | 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5922BEUI+ | 功能描述:熱插拔功率分布 48V Single-Port Network Power Switch RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。