- 您現在的位置：買賣IC網 > Datasheet目錄43 > MAX5929BEEG+ (Maxim Integrated)IC HOT SWAP CTLR QUAD 24QSOP Datasheet資料下載
參數資料
| 型號： | MAX5929BEEG+ |
| 廠商： | Maxim Integrated |
| 文件頁數： | 22/23頁 |
| 文件大小： | 340K |
| 描述： | IC HOT SWAP CTLR QUAD 24QSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 類型： | 熱交換控制器 |
| 應用： | 通用 |
| 內部開關： | 無 |
| 電源電壓： | 1 V ~ 15 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 24-QSOP |
| 包裝： | 管件 |
Layout Considerations
To take full tracking advantage of the switch response
time to an output fault condition, it is important to keep
all traces as short as possible and to maximize the
high-current trace dimensions to reduce the effect of
undesirable parasitic inductance. Place the
MAX5927A/MAX5929AMAX5929D close to the cards
connector. Use a ground plane to minimize impedance
and inductance. Minimize the current-sense resistor
trace length (<10mm), and ensure accurate current
sensing with Kelvin connections (Figure 13).
When the output is short circuited, the voltage drop
across the external MOSFET becomes large. Hence, the
power dissipation across the switch increases, as does
the die temperature. An efficient way to achieve good
power dissipation on a surface-mount package is to lay
out two copper pads directly under the MOSFET pack-
age on both sides of the board. Connect the two pads
to the ground plane through vias, and use enlarged
copper mounting pads on the topside of the board.
Low-Voltage, Quad, Hot-Swap
Controllers/Power Sequencers
22 _______________________________________________________________________ ________________________________________________ __________________________________ ___________________
MAX5927A
MAX5929AMAX5929D
GND
Q4
Q3
Q2
Q1
V
1
ON1
ON2
ON3
ON4
GND
ON1
OUT1
OUT2
*MAX5927A ONLY.
**OPTIONAL COMPONENT.
OUT3
OUT4
1nF
16V
STAT1
STAT2
STAT3
STAT4
ON2
ON3
ON4
REMOVABLE CARD
BACKPLANE
V
2
V
3
V
4
R
SENSE1
R
SENSE2
R
SENSE3
R
SENSE4
R
LIM1
**
R
LIM2
**
R
LIM3
**
R
LIM4
**
R
LIM
**
Typical Operating Circuit
Figure 13. Kelvin Connection for the Current-Sense Resistors
SENSE RESISTOR
HIGH-CURRENT PATH
MAX5927A
MAX5929AMAX5929D
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5930AEEG+ | IC HOT SWAP CTLR PWR SEQ 24QSOP |
| MAX5932ESA+T | IC HOT-SWAP CONTROLLER 8-SOIC |
| MAX5933EESA+ | IC HOT-SWAP CONTROLLER 8-SOIC |
| MAX5934EEE+ | IC HOT-SWAP CONTROLLER 16-QSOP |
| MAX5935EAX+ | IC CTRLR POWER QUAD 36-SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5929BEEG+ | 功能描述:熱插拔功率分布 Quad Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5929BEEG+T | 功能描述:熱插拔功率分布 Quad Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5929CEEG+ | 功能描述:熱插拔功率分布 Quad Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5929CEEG+T | 功能描述:熱插拔功率分布 Quad Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5929DEEG+ | 功能描述:熱插拔功率分布 Quad Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。