- 您現在的位置：買賣IC網 > Datasheet目錄43 > MAX5933EESA+ (Maxim Integrated)IC HOT-SWAP CONTROLLER 8-SOIC Datasheet資料下載
參數資料
| 型號： | MAX5933EESA+ |
| 廠商： | Maxim Integrated |
| 文件頁數： | 10/15頁 |
| 文件大小： | 269K |
| 描述： | IC HOT-SWAP CONTROLLER 8-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 100 |
| 類型： | 熱交換控制器 |
| 應用： | 通用 |
| 內部開關： | 無 |
| 電源電壓： | 33 V ~ 80 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 管件 |
Positive High-Voltage, Hot-Swap Controllers
10 ______________________________________________________________________________________
Applications Information
Hot-Circuit Insertion
When circuit boards are inserted into a live backplane,
the supply bypass capacitors on the boards draw high
peak currents from the backplane power bus as they
charge up. The transient currents can permanently
damage the connector pins and glitch the system sup-
ply, causing other boards in the system to reset.
Power-Up Sequence
The power supply on a board is controlled by placing
an external n-channel MOSFET (Q1) in the power path
(Figure 5). Resistor R
SENSE
provides current detection
and capacitor C1 provides control of the GATE slew
rate. Resistor R6 provides current control-loop compen-
sation, while R5 prevents high-frequency oscillations in
Q1. Resistors R1 and R2 provide undervoltage sensing.
After the power pins first make contact, transistor Q1 is
turned off. When the voltage at ON exceeds the turn-on
threshold voltage, the voltage on V
CC
exceeds the
undervoltage lockout threshold, and when the voltage
on TIMER is less than 1.233V, transistor Q1 turns on
(Figure 6).
The voltage at GATE rises with a slope equal to
10礎/C1 and the supply inrush current is set at:
I
INRUSH
= C
L
x 10礎/C1
When the voltage across the current-sense resistor
R
SENSE
reaches V
SENSETRIP
, the inrush current is limit-
ed by the internal current-limit circuitry that adjusts the
voltage on GATE to maintain a constant voltage across
the sense resistor.
Once the voltage at the output has reached its final value,
as sensed by resistors R3 and R4, PWRGD goes high or
PWRGD goes low.
Short-Circuit Protection
The MAX5933_/MAX5947_ feature a programmable fold-
back current limit with an electronic circuit breaker that
protects against short circuits or excessive supply cur-
rents. The current limit is set by placing a sense resistor
between V
CC
(pin 8) and SENSE (pin 7).
To prevent excessive power dissipation in the pass
transistor and to prevent voltage spikes on the input
supply during short-circuit conditions at the output, the
current folds back as a function of the output voltage
that is sensed at FB (Figure 7).
When the voltage at FB is 0V, the current-limit circuit
drives GATE to force a constant 12mV drop across the
sense resistor. As the output voltage at FB increases,
the voltage across the sense resistor increases until FB
reaches 0.5V. At this point, the voltage across the
sense resistor is held constant at 47mV.
The maximum current limit is calculated as:
I
LIMIT
= 47mV / R
SENSE
For a 0.025& sense resistor, the current limit is set at
1.88A and folds back to 480mA when the output is
shorted to ground.
The MAX5933_/MAX5947_ also feature a variable over-
current response time. The time required to regulate
Q1s drain current depends on:
1) Q1s input capacitance
2) GATE capacitor C1 and compensation resistor R6
3) The internal delay from SENSE to GATE
Figure 8 shows the delay from a voltage step at SENSE
until GATE voltage starts falling, as a function of
overdrive.
POWER-UP WAVEFORMS
I
SENSE
2A/div
PWRGD
50V/div
OUTPUT
50V/div
GATE
50V/div
20ms/div
Figure 6. Power-Up Waveforms
V
CC
- V
SENSE
V
FB
12mV
47mV
0.5V
0V
Figure 7. Current-Limit Sense Voltage vs. Feedback Voltage
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5934EEE+ | IC HOT-SWAP CONTROLLER 16-QSOP |
| MAX5935EAX+ | IC CTRLR POWER QUAD 36-SSOP |
| MAX5937LCESA+ | IC HOT-SWAP CTRLR -48V 8-SOIC |
| MAX5938LEEE+ | IC HOT-SWAP CTRLR -48V 16-QSOP |
| MAX5939EESA+ | IC HOT-SWAP CTRLR -48V 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5933EESA+ | 功能描述:熱插拔功率分布 Positive Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5933EESA+T | 功能描述:熱插拔功率分布 Positive Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5933EESA-T | 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5934AEEE | 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5934AEEE+ | 功能描述:熱插拔功率分布 Positive Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。