- 您現在的位置：買賣IC網 > Datasheet目錄43 > MAX5950ETJ+ (Maxim Integrated)IC PWM CTRL HOT-SW 12V 32TQFN-EP Datasheet資料下載
參數資料
| 型號： | MAX5950ETJ+ |
| 廠商： | Maxim Integrated |
| 文件頁數： | 16/28頁 |
| 文件大小： | 552K |
| 描述： | IC PWM CTRL HOT-SW 12V 32TQFN-EP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 60 |
| 類型： | 熱交換控制器 |
| 應用： | 通用型，PCI Express? |
| 內部開關： | 無 |
| 電源電壓： | 8 V ~ 16 V，±5V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 32-TQFN-EP（5x5） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
12V PWM Controller with Hot-Swap
16 ______________________________________________________________________________________
Power-Good Sequencing (PGOOD, SENSE)
The PGOOD outputs and DCENI inputs can be daisy-
chained to generate power sequencing. The PGOOD
output is pulled high when the voltage at SENSE is
above V
REF
(800mV typ). Connect a resistive divider
from the power-supply output voltage to SENSE to
AGND to set the power-good threshold. See Figure 1
and the Typical Operating Circuits.
Error Amplifier
The output of the internal error amplifier (COMP) is avail-
able for frequency compensation (see the
Compensation Design Guidelines section). The inverting
input is FB; the output is COMP. The error amplifier has
an 80dB open-loop gain and a 2.5MHz GBW product.
See the Typical Operating Characteristics section for
the Open-Loop Gain and Phase vs. Frequency graph.
PWM Comparator
An internal ramp is compared against the output of the
error amplifier to generate the PWM signal. The ampli-
tude of the ramp, V
RAMP,
is 1.8V.
Output Short-Circuit Protection
(Hiccup Mode)
The current-limit circuit employs a lossless valley cur-
rent-limiting algorithm that uses the MOSFETs on-resis-
tance as the current-sensing element. Once the
high-side MOSFET turns off, the voltage across the low-
side MOSFET is monitored. If the voltage across the
low-side MOSFET (R
DS(ON)
x I
INDUCTOR
) does not
exceed the current-limit threshold, the high-side
MOSFET turns on normally at the start of the next cycle.
If the voltage across the low-side MOSFET exceeds the
current-limit threshold just before the beginning of a
new PWM cycle, the controller skips that cycle. During
severe overload or short-circuit conditions, the switch-
ing frequency of the device appears to decrease
because the on-time of the low-side MOSFET extends
beyond a clock cycle.
If the current-limit threshold is exceeded for eight cumu-
lative clock cycles (N
CL
), the device shuts down (both
DH and DL are pulled low) for 512 clock cycles (hiccup
timeout) and restarts with a soft-start sequence. If three
consecutive cycles pass without a current-limit event,
the count of N
CL
is cleared (Figure 2). Hiccup mode
protects against continuous output short circuit.
Thermal-Overload Protection
The MAX5950 features an integrated thermal-overload
protection with temperature hysteresis. Thermal-over-
load protection limits the total power dissipation in the
device and protects it in the event of an extended ther-
mal fault condition. When the die temperature exceeds
+135癈, an internal thermal sensor shuts down the
device, turning off the power MOSFETs and allowing
the die to cool. After the die temperature falls by
+15癈, the part restarts with a soft-start sequence.
Hot-Swap Controller Design
Procedures
Setting the Undervoltage Lockout
Connect an external resistive divider from IN to HUVLO
to AGND to override the internal hot-swap UVLO
divider. The rising threshold at HUVLO is set to 1.220V
with 120mV hysteresis. First, select the HUVLO to
AGND resistor (R2), then calculate the resistor from IN
to HUVLO (R1) using the following equation:
where V
IN
is the input voltage at which the hot-swap
controller needs to turn on, V
HUVLO
= 1.220V, and R2
is chosen to be less than 20k& (see Figure 3).
Leave HUVLO unconnected for the default hot-swap
UVLO threshold. In this case, an internal voltage-
divider monitors the supply voltage at IN and allows
startup when IN rises above 7V (typ).
R
R
V
V
IN
HUVLO
1
2
1
=
?/DIV>
主站蜘蛛池模板：
讷河市|
洛宁县|
商都县|
南康市|
沈阳市|
绿春县|
类乌齐县|
新巴尔虎左旗|
包头市|
景宁|
澄江县|
泰来县|
长丰县|
高碑店市|
定安县|
五常市|
盐源县|
曲靖市|
洪江市|
新化县|
库尔勒市|
葫芦岛市|
屏山县|
阿克苏市|
宁乡县|
浏阳市|
清新县|
同德县|
攀枝花市|
麻城市|
塘沽区|
镇康县|
哈巴河县|
新干县|
炎陵县|
咸丰县|
东兰县|
壤塘县|
申扎县|
兴隆县|
凤翔县|
?/DIV>
?/DIV>
?/DIV>
?/DIV>
IN
R1
R2
HUVLO
Figure 3. External Hot-Swap UVLO Divider
CURRENT LIMIT
COUNT OF 8
N
CL
IN
CLR
INITIATE HICCUP
TIMEOUT
N
HT
COUNT OF 3
N
CLR
IN
CLR
Figure 2. Hiccup-Mode Block Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5952CUAX+ | IC PSE CNTRLR FOR POE 36-SSOP |
| MAX5953DUTM+ | IC INTERFACE 802.3AF 48TQFN |
| MAX5954LETX+T | IC PCI EXP/HOT-PLUG CTRLR 36TQFN |
| MAX5955BEEE+ | IC DUAL HOT-SWAP CTRLR 16-QSOP |
| MAX5957AETN+T | IC TRPL PCI EXP/HOT-PLUG 56-TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5950ETJ+ | 功能描述:電壓模式 PWM 控制器 12V PWM Controller w/Hot-Swap RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| MAX5950ETJ+T | 功能描述:電壓模式 PWM 控制器 12V PWM Controller w/Hot-Swap RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| MAX5950ETJ-T | 功能描述:電壓模式 PWM 控制器 RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| MAX5950EVKIT | 制造商:Maxim Integrated Products 功能描述:12V PWM CONTROLLER WITH HOT-SWAP - Rail/Tube |
| MAX5951ETJ | 功能描述:電壓模式 PWM 控制器 RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。