- 您現在的位置：買賣IC網 > Datasheet目錄43 > MAX5954LETX+T (Maxim Integrated)IC PCI EXP/HOT-PLUG CTRLR 36TQFN Datasheet資料下載
參數資料
| 型號： | MAX5954LETX+T |
| 廠商： | Maxim Integrated |
| 文件頁數： | 19/22頁 |
| 文件大小： | 1027K |
| 描述： | IC PCI EXP/HOT-PLUG CTRLR 36TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | 熱交換控制器 |
| 應用： | 通用型，PCI Express? |
| 內部開關： | 無 |
| 電源電壓： | 3.3V，12V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 36-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 36-TQFN 裸露焊盤（6x6） |
| 包裝： | 帶卷 (TR) |
Applications Information
Setting the Fault Timeout Period (t
FAULT
)
t
FAULT
is the time an overcurrent or overtemperature
fault must remain for the MAX5954 to disable the main
or auxiliary outputs. Program the fault timeout period
(t
FAULT
) by connecting a resistor (R
TIM
) from TIM to GND.
t
FAULT
can be calculated by the following equation:
t
FAULT
= 166ns / & x R
TIM
The t
FAULT
programmed time duration must be chosen
according to the total capacitance load connected to
12G and 3.3G. To properly power-up the main supply
outputs, the following constraints need to be taken:
where t
SU
= 2 x t
FAULT
and where:
1) I
CHG
= 5礎.
2) V
GATE
= 18.4V for 12G and V
GATE
= 9.4V for 3.3G.
3) C
LOAD
is the total capacitance load at the gate.
Maximum and minimum values for R
TIM
are 500k& and
500&, respectively. Leave TIM floating for a default
t
FAULT
of 11ms.
Setting the Power-On-Reset
Timeout Period (t
POR_HL
)
t
POR_HL
is the time from when the gate voltages of all
outputs reach their power-good threshold to when
PWRGD pulls low. Program the power-on-reset timeout
period (t
POR
) by connecting a resistor (R
PORADJ
) from
PORADJ to GND. t
POR_HL
can be calculated by the fol-
lowing equation:
t
POR_HL
= 2.5祍 / & x R
PORADJ
Maximum and minimum values for R
PORADJ
are 500k&
and 500&, respectively. Leave PORADJ floating for a
default t
POR
of 160ms.
Component Selection
Select the external n-channel MOSFET according to the
applications current requirement. Limit the switch
power dissipation by choosing a MOSFET with an
R
DS_ON
low enough to have a minimum voltage drop at
full load. High R
DS_ON
causes larger output ripple if
there are pulsed loads. High R
DS_ON
can also trigger an
external undervoltage fault at full load. Determine the
MOSFETs power rating requirement to accommodate a
short-circuit condition on the board during startup. Table
3 lists MOSFETs and sense-resistor manufacturers.
Additional External Gate Capacitance
External capacitance can be added from the gate of
the external MOSFETs to GND to slow down the dV/dt
of the 12V and 3.3V outputs.
Maximum Load Capacitance
Large capacitive loads at the 12V output, the 3.3V out-
put, and the 3.3V auxiliary output can cause a problem
when inserting discharged PCI cards into live back-
planes. A fault occurs if the time needed to charge the
capacitance of the board is greater than the typical
startup time (2 x t
FAULT
). The MAX5954 can withstand
large capacitive loads due to their adjustable startup
times and adjustable current-limit thresholds. Calculate
the maximum load capacitance as follows:
V
OUT
is either the 3.3V output, the 12V output, or the
3.3V auxiliary output.
C
t
I
V
LOAD
SU LIM
<
?/DIV>
t
V
C
I
SU
GATE
LOAD
H
e
?/DIV>
Single PCI Express, Hot-Plug
Controller
______________________________________________________________________________________ 19
Table 3. Component Manufacturers
COMPONENT
MANUFACTURER
PHONE
WEBSITE
Vishay-Dale
402-564-3131
www.vishay.com
Sense Resistor
IRC
704-264-8861
www.irctt.com
Fairchild
888-522-5372
www.fairchildsemi.com
International Rectifier
310-322-3331
www.irf.com
Motorola
602-244-3576
www.mot-sps.com/ppd/
MOSFETs
Vishay-Siliconix
www.vishay.com
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5955BEEE+ | IC DUAL HOT-SWAP CTRLR 16-QSOP |
| MAX5957AETN+T | IC TRPL PCI EXP/HOT-PLUG 56-TQFN |
| MAX5960AECS+T | IC CTRLR HOT-PLUG QD 80-TQFP |
| MAX5963UTL+T | IC HOT SWAP DIO ORING CTL 40TQFN |
| MAX5965AEAX+ | IC PSE CTRLR FOR POE 36SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5954LEVCMAXQUSB | 功能描述:電源管理IC開發工具 MAX5954LMAXQUSB EVAL KIT RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| MAX5954LEVKIT | 功能描述:電源管理IC開發工具 Evaluation Kit/Evaluation System for the MAX5954L/MAX5954A RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| MAX5955AEEE | 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5955AEEE+ | 功能描述:熱插拔功率分布 Dual Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5955AEEE+T | 功能描述:熱插拔功率分布 Dual Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。