- 您現在的位置：買賣IC網 > Datasheet目錄43 > MAX5971AETI+ (Maxim Integrated)IC CTRLR PD IEEE 802.3AF 28WQFN Datasheet資料下載
參數資料
| 型號： | MAX5971AETI+ |
| 廠商： | Maxim Integrated |
| 文件頁數： | 5/22頁 |
| 文件大小： | 2126K |
| 描述： | IC CTRLR PD IEEE 802.3AF 28WQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 60 |
| 類型： | 以太網供電控制器 PD 開關（PoE） |
| 應用： | 供電設備（PSE） |
| 內部開關： | 是 |
| 電流限制： | 可調 |
| 電源電壓： | 32 V ~ 60 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 28-TQFN-EP（5x5） |
| 包裝： | 管件 |
_______________________________________________________________________________________ 5
Single-Port, 40W, IEEE 802.3af/802.3at PSE
Controller with Integrated MOSFET
Note 2: This device is production tested at T
A
= +25NC. Limits at T
A
= -40NC and +85NC are guaranteed by design.
Note 3: If ILIM1 and ILIM2 are both unconnected, Class 5 detection is disabled. See the Class 5 PD Classification section and Table 3 for
details and settings.
Note 4: R
DOK
= (V
OUT2
- V
OUT1
)/(I
DET2
- I
DET1
). V
OUT1
, V
OUT2
, I
DET2
, and I
DET1
represent the voltage at OUT and the current at
DET during phase 1 and 2 of the detection, respectively.
Note 5: If Class 5 is enabled, this is the classification current thresholds from Class 4 to Class 5.
ELECTRICAL CHARACTERISTICS (continued)
(V
AGND
- V
EE
= 32V to 60V, T
A
= -40NC to +85NC, all voltages are referenced to V
EE
, unless otherwise noted. Typical values are at
V
AGND
- V
EE
= +54V, T
A
= +25NC. Currents are positive when entering the pin and negative otherwise.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
DIGITAL INPUTS/OUTPUTS (Voltages referenced to V
EE
)
Digital Input Low
V
IL
0.8
V
Digital Input High
V
IH
2.4
V
Internal Input Pullup Current
I
PU
Pullup current to internal digital supply to
set default values
3
5
7
FA
LED Output Low Voltage
V
LED_LOW
I
LED
= 10mA, PWM disabled, port power-on
0.8
V
LED Output Leakage
I
LED_LEAK
PWM disabled, shutdown mode,
V
LED
= 60V
10
FA
PWM Frequency
25
kHz
PWM Duty Cycle
6.25
%
TIMING
Startup Time
t
START
Time during which a current limit set to
420mA is allowed, starts when power is
turned on
50
60
70
ms
Fault Time
t
FAULT
Maximum allowed time for an overcurrent
condition set by I
CUT
after startup
50
60
70
ms
Detection Reset Time
t
ME
Time allowed for the port voltage to reset
before detection starts
80
90
ms
Detection Time
t
DET
Maximum time allowed before detection is
completed
330
ms
Midspan Mode Detection Delay
t
DMID
2
2.2
2.4
s
Classification Time
t
CLASS
Time allowed for classification
19
23
ms
Mark Event Time
Time allowed for mark event
7
9
11
ms
V
EEUVLO
Turn-On Delay
t
DLY
Time V
AGND
must be above the V
EEUVLO
thresholds before the device operates
5.2
ms
Restart Timer
t
RESTART
Time the device waits before turning on
after an overcurrent fault
16 x
t
FAULT
ms
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5972AETE+T | IC CONTROLLER INTERFACE 16TQFN |
| MAX5978ETJ+ | IC CTLR HOT-SWAP 32TQFN |
| MAX5981BETE+ | IC CTRLR PD IEEE 802.3AF 16TQFN |
| MAX5986AETE+ | IC POE SWITCH PSE 16TQFN |
| MAX6509CAZK/V+T | IC TEMP SWITCH RES-PROG 5TSOT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5971AETI+ | 功能描述:熱插拔功率分布 IEEE 802.3af/at PSE Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5971AETI+T | 功能描述:熱插拔功率分布 IEEE 802.3af/at PSE Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5971AETI+W | 制造商:Maxim Integrated Products 功能描述:IEEE802.3 AT PSE SWITCH - Rail/Tube |
| MAX5971AEVKIT | 功能描述:電源管理IC開發工具 RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| MAX5971AEVKIT+ | 制造商:Maxim Integrated Products 功能描述:PD INTERFACE CONTROLLER - Boxed Product (Development Kits) |
發布緊急采購，3分鐘左右您將得到回復。