- 您現在的位置：買賣IC網 > PDF目錄382287 > MAX8538EEI (Electronic Theatre Controls, Inc.) BNC RCPT, PAN-MT, INSULATED, SOLDER PDF資料下載
參數資料
| 型號： | MAX8538EEI |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | BNC RCPT, PAN-MT, INSULATED, SOLDER |
| 中文描述： | 塑封器件 |
| 文件頁數： | 4/8頁 |
| 文件大小： | 100K |
| 代理商： | MAX8538EEI |
V. Quality Assurance Information
A. Quality Assurance Contacts:
B. Outgoing Inspection Level: 0.1% for all electrical parameters guaranteed by the Datasheet.
0.1% For all Visual Defects.
C. Observed Outgoing Defect Rate: < 50 ppm
D. Sampling Plan: Mil-Std-105D
VI. Reliability Evaluation
A. Accelerated Life Test
The results of the 135
°
C biased (static) life test are shown in
Table 1
. Using these results, the Failure
Rate (
λ
) is calculated as follows:
λ
= 1 = 1.83 (Chi square value for MTTF upper limit)
MTTF
192 x 4389 x 48 x 2
Temperature Acceleration factor assuming an activation energy of 0.8eV
λ
= 22.62 x 10
-9
λ
= 22.62 F.I.T. (60% confidence level @ 25
°
C)
This low failure rate represents data collected from Maxim’s reliability monitor program. In addition to
routine production Burn-In, Maxim pulls a sample from every fabrication process three times per week and subjects
it to an extended Burn-In prior to shipment to ensure its reliability. The reliability control level for each lot to be
shipped as standard product is 59 F.I.T. at a 60% confidence level, which equates to 3 failures in an 80 piece
sample. Maxim performs failure analysis on any lot that exceeds this reliability control level. Attached Burn-In
Schematic (Spec. # 06-6190) shows the static Burn-In circuit. Maxim also performs quarterly 1000 hour life test
monitors. This data is published in the Product Reliability Report (
RR-1M
).
B. Moisture Resistance Tests
Maxim pulls pressure pot samples from every assembly process three times per week. Each lot sample
must meet an LTPD = 20 or less before shipment as standard product. Additionally, the industry standard
85
°
C/85%RH testing is done per generic device/package family once a quarter.
C. E.S.D. and Latch-Up Testing
The PN02-1
die type has been found to have all pins able to withstand a transient pulse of
±
<200V, per Mil-
Std-883 Method 3015 (reference attached ESD Test Circuit). Latch-Up testing has shown that this device
withstands a current of
±
250mA.
Jim Pedicord (Manager, Reliability Operations)
Bryan Preeshl (Managing Director of QA
)
Kenneth Huening (Vice President)
相關PDF資料 |
PDF描述 |
|---|---|
| MAX8539 | WIRE; 24; GRN; 1007/1569, 300V, PVC, CU/TN, (1004563) |
| MAX9022AKA-T | Micropower, Ultra-Small, Single/Dual/Quad, Single-Supply Comparators |
| MAX9024ASD | Micropower, Ultra-Small, Single/Dual/Quad, Single-Supply Comparators |
| MAX9022ASA | Octal Buffers/Drivers With 3-State Outputs 20-CFP -55 to 125 |
| MAX9024 | Octal Bus Transceivers With 3-State Outputs 20-LCCC -55 to 125 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX8538EEI+ | 功能描述:DC/DC 開關控制器 Dual-Synchronous Buck Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX8538EEI+T | 功能描述:DC/DC 開關控制器 Dual-Synchronous Buck Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX8538EEI-T | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX8538EVKIT | 功能描述:DC/DC 開關控制器 Evaluation Kit for the MAX8538 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX8539EEI | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。