- 您現在的位置：買賣IC網 > PDF目錄16786 > MAX9716EVKIT (Maxim Integrated Products)EVAL KIT FOR MAX9716 PDF資料下載
參數資料
| 型號： | MAX9716EVKIT |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/21頁 |
| 文件大小： | 0K |
| 描述： | EVAL KIT FOR MAX9716 |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 放大器類型： | AB 類 |
| 輸出類型： | 1-通道（單聲道） |
| 在某負載時最大輸出功率 x 通道數量： | 1.4W x 1 @ 4 歐姆 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | 0°C ~ 70°C |
| 板類型： | 完全填充 |
| 已用 IC / 零件： | MAX9716，MAX9717 |
| 已供物品： | 板 |
MAX9716/MAX9717
Applications Information
BTL Amplifier
The MAX9716/MAX9717 are designed to drive a load
differentially, a configuration referred to as bridge-tied
load or BTL. The BTL configuration (Figure 1) offers
advantages over the single-ended configuration, where
one side of the load is connected to ground. Driving the
load differentially doubles the output voltage compared
to a single-ended amplifier under similar conditions.
Thus, the differential gain of the device is twice the
closed-loop gain of the input amplifier. The effective
gain is given by:
Substituting 2 x VOUT(P-P) for VOUT(P-P) into the following
equations yields four times the output power due to
doubling of the output voltage:
There is no net DC voltage across the load because the
differential outputs are each biased at midsupply. This
eliminates the need for DC-blocking capacitors
required for single-ended amplifiers. These capacitors
can be large and expensive, consume board space,
and degrade low-frequency performance.
Power Dissipation and Heat Sinking
Under normal operating conditions, the MAX9716/
MAX9717 dissipate a significant amount of power. The
maximum power dissipation for each package is given
in the
Absolute Maximum Ratings section under
Continuous Power Dissipation or can be calculated by
the following equation:
where TJ(MAX) is +150°C, TA is the ambient temperature,
and
θJA is the reciprocal of the derating factor in °C/W as
specified in the
Absolute Maximum Ratings section. For
example,
θJA of the TDFN package is 41°C/W.
The increase in power delivered by the BTL configuration
directly results in an increase in internal power dissipation
over the single-ended configuration. The maximum power
dissipation for a given VCC and load is given by the
following equation:
If the power dissipation for a given application exceeds
the maximum allowed for a given package, reduce
power dissipation by increasing the ground plane heat-
sinking capability and the size of the traces to the device
(see the
Layout and Grounding section). Other methods
for reducing power dissipation are to reduce VCC,
increase load impedance, decrease ambient tempera-
ture, reduce gain, or reduce input signal.
Thermal-overload protection limits total power dissipation
in the MAX9716/MAX9717. Thermal protection circuitry
disables the amplifier output stage when the junction
temperature exceeds +160°C. The amplifiers are
enabled once the junction temperature cools by 15°C. A
pulsing output under continuous thermal-overload condi-
tions results as the device heats and cools.
Fixed Gain
The MAX9717B, MAX9717C, and MAX9717D feature
internally fixed gains of 6dB, 9dB, and 12dB, respec-
tively (see the
Selector Guide). Fixed gain simplifies
designs, reduces pin count, decreases required foot-
print size, and eliminates external gain-setting resistors.
Resistors RIN and RF shown in the MAX9717B/C/D
Typical Operating Circuit are used to achieve each
fixed gain.
P
V
R
DISS MAX
CC
L
()
=
2
π
P
TT
DISSPKG MAX
J MAX
A
JA
()
=
θ
P
V
R
OUT
RMS
L
=
2
V
RMS
OUT P P
()
=
22
A
R
V
F
IN
=×
2
Low-Cost, Mono, 1.4W BTL Audio
Power Amplifiers
10
______________________________________________________________________________________
+1
VOUT(P-P)
2 x VOUT(P-P)
VOUT(P-P)
-1
Figure 1. Bridge-Tied Load Configuration
相關PDF資料 |
PDF描述 |
|---|---|
| 462A034-25/225-0 | BOOT MOLDED |
| H1AXS-1436G | IDC CABLE - HSC14S/AE14G/X |
| RBC15DCAH-S189 | CONN EDGECARD 30POS R/A .100 SLD |
| MC1403BDR2 | IC VREF SERIES PREC 2.5V 8-SOICN |
| MAX9700BEVKIT | EVAL KIT FOR MAX9700 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9717AEBL | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX9717AEBL+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX9717AEBL+T | 功能描述:音頻放大器 Mono 1.4W BTL Audio Power Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9717AEBL-T | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9717AETA | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。