- 您現在的位置：買賣IC網 > PDF目錄16782 > MAX97200AEVKIT+ (Maxim Integrated Products)KIT EVALUATION FOR MAX97200 PDF資料下載
參數資料
| 型號： | MAX97200AEVKIT+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/13頁 |
| 文件大小： | 0K |
| 描述： | KIT EVALUATION FOR MAX97200 |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 系列： | DirectDrive® |
| 放大器類型： | G 類 |
| 輸出類型： | 耳機，2-通道（立體聲） |
| 電源電壓： | 1.8V |
| 板類型： | 完全填充 |
| 已用 IC / 零件： | MAX97200A |
| 已供物品： | 板 |
Low-Power, Low-Offset, Dual Mode, Class H
DirectDrive Headphone Amplifier
MAX97200
10
RIN is the amplifier’s input resistance value. Choose CIN
such that f-3dB is well below the lowest frequency of
interest. Setting f-3dB too high affects the amplifier’s low
frequency. Capacitors with higher voltage coefficients,
such as ceramics, result in increased distortion at low
frequencies.
Charge-Pump Capacitor Selection
Use capacitors with an ESR less than 100mI for opti-
mum performance. Low ESR ceramic capacitors mini-
mize the output resistance of the charge pump. For best
performance over the extended temperature range,
select capacitors with an X7R dielectric.
Flying Capacitor (C1)
The value of the flying capacitor (C1) affects the load
regulation and output resistance of the charge pump. A
C1 value that is too small degrades the device’s ability
to provide sufficient current drive, which leads to a loss
of output voltage. Connect a 1FF capacitor between C1P
and C1N.
Output Capacitors (C2, C3)
The output capacitor value and ESR directly affect the
ripple at PVSS. Increasing the value of C2 and C3 reduc-
es output ripple. Likewise, decreasing the ESR of C2 and
C3 reduces both ripple and output resistance. Lower
capacitance values can be used in systems with low
maximum output power levels. Connect a 1FF capaci-
tor between PVDD and PGND. Connect a 1FF capacitor
between PVSS and PGND.
RF Susceptibility
Improvements to both layout and component selec-
tion can decrease the MAX97200 susceptibility to RF
noise and prevent RF signals from being demodulated
into audible noise. Trace lengths should be kept below
of the wavelength of the RF frequency of interest.
Minimizing the trace lengths prevents the traces from
functioning as antennas and coupling RF signals into the
MAX97200. The wavelength (λ) in meters is given by:
λ
= c/f
where c = 3 x 108 m/s, and f is the RF frequency of
interest.
Route audio signals to the middle layers of the PCB to
allow the ground planes above and below to shield them
from RF interference. Ideally, the top and bottom layers
of the PCB should primarily be ground planes to create
effective shielding.
Additional RF immunity can also be obtained from rely-
ing on the self-resonant frequency of capacitors as
it exhibits the frequency response similar to a notch
filter. Depending on the manufacturer, 10pF to 20pF
capacitors typically exhibit self resonance at RF frequen-
cies. These capacitors when placed at the input pins
can effectively shunt the RF noise at the inputs of the
MAX97200. For these capacitors to be effective, provide
a low-impedance, low-inductance path from the capaci-
tors to the ground plane. Do not use microvias to con-
nect to the ground plane as these vias do not conduct
well at RF frequencies. Figure 3 shows headphone RF
immunity with a well laid out PCB.
Layout and Grounding
Proper layout and grounding are essential for optimum
performance. Use large traces for the power-supply
inputs and amplifier outputs to minimize losses due to
parasitic trace resistance, as well as route heat away
from the device. Good grounding improves audio per-
formance, minimizes crosstalk between channels, and
prevents switching noise from coupling into the audio
signal. Connect PGND and GND together at a single
point on the PCB. Route PGND and all traces that carry
switching transients away from GND, and the traces and
components in the audio signal path.
Connect C2 to the PGND plane. Place the charge-pump
capacitors (C1, C2) as close as possible to the device.
Bypass PVDD with a 1FF capacitor to PGND. Place the
bypass capacitors as close as possible to the device.
Figure 3. Headphone RF Immunity
HEADPHONE RF IMMUNITY
vs. FREQUENCY
FREQUENCY (MHz)
OUTPUT
NOISE
(dBV)
2500
2000
1500
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
-100
1000
3000
LEFT CHANNEL
RIGHT CHANNEL
相關PDF資料 |
PDF描述 |
|---|---|
| B78108T1682K | CHOKE RF 6.8UH 250MA AXIAL |
| H2MXH-5018G | DIP CABLE - HDM50H/AE50G/X |
| H2MXS-5018G | DIP CABLE - HDM50S/AE50G/X |
| GBM43DCWD | CONN EDGECARD 86POS DIP .156 SLD |
| EBC35DCMN-S288 | CONN EDGECARD 70POS .100 EXTEND |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX97200AEVKIT+ | 功能描述:音頻 IC 開發工具 MAX97200A Eval Kit RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| MAX97200AEWC+ | 制造商:Maxim Integrated Products 功能描述:HIGH EFFICIENCY HEADPHONE AMPLIFIER - Rail/Tube |
| MAX97200AEWC+T | 功能描述:音頻放大器 Class H DirectDrive Headphone Amplifier RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX97200BEWC+T | 功能描述:音頻放大器 Class H DirectDrive Headphone Amplifier RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9720AEBE | 制造商:Maxim Integrated Products 功能描述:50MW, DIRECTDRIVE, STEREO HEADPHONE AMPLIFIER - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。