- 您現在的位置：買賣IC網 > PDF目錄16784 > MAX9768EVKIT+ (Maxim Integrated Products)EVALUATION KIT FOR MAX9768 PDF資料下載
參數資料
| 型號： | MAX9768EVKIT+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 8/26頁 |
| 文件大小： | 0K |
| 描述： | EVALUATION KIT FOR MAX9768 |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 放大器類型： | D 類 |
| 輸出類型： | 1-通道（單聲道） |
| 在某負載時最大輸出功率 x 通道數量： | 10W x 1 @ 8 歐姆 |
| 電源電壓： | 4.5 V ~ 14 V |
| 工作溫度： | -40°C ~ 85°C |
| 板類型： | 完全填充 |
| 已用 IC / 零件： | MAX9768 |
| 已供物品： | 板 |
MAX9768
10W Mono Class D Speaker
Amplifier with Volume Control
16
______________________________________________________________________________________
Bit Transfer
One data bit is transferred during each SCL cycle. The
data on SDA must remain stable during the high period
of the SCL pulse. Changes in SDA while SCL is high
are control signals (see the
START and STOP
Conditions section). SDA and SCL idle high when the
I2C bus is not busy.
START and STOP Conditions
A master device initiates communication by issuing a
START condition. A START condition is a high-to-low
transition on SDA with SCL high. A STOP condition is a
low-to-high transition on SDA while SCL is high (Figure 4).
A START (S) condition from the master signals the
beginning of a transmission to the MAX9768. The mas-
ter terminates transmission, and frees the bus, by issu-
ing a STOP (P) condition. The bus remains active if a
REPEATED START (Sr) condition is generated instead
of a STOP condition.
Early STOP Conditions
The MAX9768 recognizes a STOP condition at any point
during data transmission except if the STOP condition
occurs in the same high pulse as a START condition.
Slave Address
The slave address of the MAX9768 is 8 bits and con-
sisting of 3 fields: the first field is 5 bits wide and is
fixed (10010). The second is a 2-bit field, which is set
through ADDR2 and ADDR1 (externally connected as
logic-high or low). Third field is a R/W flag bit. Set R/W
= 0 to write to the slave. A representation of the slave
address is shown in Table 3.
When ADDR1 and ADDR2 are connected to GND, seri-
al interface communication is disabled. Table 4 sum-
marizes the slave address of the device as a function of
ADDR1 and ADDR2.
Acknowledge
The acknowledge bit (ACK) is a clocked 9th bit that the
MAX9768 uses to handshake receipt each byte of data
(Figure 5). The MAX9768 pulls down SDA during the
master-generated 9th clock pulse. The SDA line must
remain stable and low during the high period of the
acknowledge clock pulse. Monitoring ACK allows for
detection of unsuccessful data transfers. An unsuc-
cessful data transfer occurs if a receiving device is
busy or if a system fault has occurred. In the event of
an unsuccessful data transfer, the bus master can re-
attempt communication.
SCL
SDA
START
CONDITION
STOP
CONDITION
REPEATED
START
CONDITION
START
CONDITION
tHD,STA
tSU,STA
tHD,STA
tSP
tBUF
tSU,STO
tLOW
tSU,DAT
tHD,DAT
tHIGH
tR
tF
Figure 3. 2-Wire Serial-Interface Timing Diagram
SCL
SDA
SSr
P
Figure 4. START, STOP, and REPEATED START Conditions
相關PDF資料 |
PDF描述 |
|---|---|
| ECC13DREH-S93 | CONN EDGECARD 26POS .100 EYELET |
| H6PPS-2406M | DIP CABLE - HDP24S/AE24M/HDP24S |
| V300C15E150B | CONVERTER MOD DC/DC 15V 150W |
| H3AAS-1606M | IDC CABLE - HSC16S/AE16M/HSC16S |
| 382A046-4-0 | BOOT MOLDED |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9768EVKIT+ | 功能描述:音頻 IC 開發工具 MAX9768 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| MAX976ESA | 功能描述:校驗器 IC Dual High Speed Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX976ESA+ | 功能描述:校驗器 IC Dual High Speed Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX976ESA+T | 功能描述:校驗器 IC Dual High Speed Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX976ESA-T | 功能描述:校驗器 IC Dual High Speed Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。