- 您現在的位置：買賣IC網 > PDF目錄16783 > MAX98400BEVKIT+ (Maxim Integrated Products)KIT EVAL FOR MAX98400B PDF資料下載
參數資料
| 型號： | MAX98400BEVKIT+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 11/26頁 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR MAX98400B |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 系列： | * |
Stereo, High-Power, Class D Amplifiers
MAX98400A/MAX98400B
19
Inductor-Based Output Filters
Some applications use the ICs with a full inductor-/
capacitor-based (L/C) output filter. See Figure 4 for the
correct connections of these components.
The load impedance of the speaker determines the filter
component selection (Table 3).
Inductors L1 and L2 and capacitor C1 form the primary
output filter. Capacitors C2 and C3 provide common-
mode filtering to reduce radiated emissions. Capacitors
C4 and C5, plus resistors R1 and R2, form a Zobel at
the output. A Zobel corrects the output loading to com-
pensate for the rising impedance of the loudspeaker.
Without a Zobel, the filter exhibits a peak response near
the cutoff frequency.
Component Selection
Input Capacitor
The input AC-coupling capacitors allow the amplifier to
automatically bias the signal to an optimum DC level.
1FF is recommended for the input capacitor.
Power Supplies
The ICs are designed to be operated from a single-
supply voltage, VPVDD, which can range from 8V to 28V.
Inside the ICs, this VPVDD supplies power for the output
FETs and other high-power circuitry, while the low-power
circuitry operates from VS, an internally generated 5V
supply (4.6V typ). VS is internally generated from a lin-
ear regulator that is powered from VPVDD. Bypass both
PVDD and VS pins to ground with a 1FF capacitor.
Internal Regulator VS
For highest efficiency operation and best thermal perfor-
mance, especially at higher VPVDD levels, the VS can be
supplied from an external 5V supply. To do this, connect
a 5V source to the VS pin (4.75V to 5.5V). When a 5V
supply is connected to the VS pin, the internal regulator
is automatically disabled and the power dissipation of
the ICs is reduced.
Supply Bypassing, Layout, and Grounding
Proper layout and grounding are essential for optimum
performance. Use wide traces for the power-supply
inputs and amplifier outputs to minimize losses due to
parasitic trace resistance. Proper grounding improves
audio performance, minimizes crosstalk between chan-
nels, and prevents switching noise from coupling into
the audio signal. Connect PGND and GND together at
a single point on the PCB. Route all traces that carry
switching transients away from GND and the traces/
components in the audio signal path.
Bypass each PVDD pin with a 0.1FF capacitor to PGND.
Place the bypass capacitors as close as possible to the
ICs. Place a 220FF capacitor between PVDD and PGND.
Bypass both PVDD and VS pins with a 1FF capacitor to
GND.
Use wide, low-resistance output traces. Current drawn
from the outputs increases as load impedance decreas-
es. High-output trace resistance decreases the power
delivered to the load. The TQFN package features an
exposed thermal pad on its underside. This pad lowers
the package’s thermal resistance by providing a heat
conduction path from the die to the PCB. Connect the
exposed thermal pad to PGND by using a large pad and
multiple vias to the PGND plane.
For best optimum thermal performance, use 2oz copper
and allow lots of PCB area around the device.
Chip Information
PROCESS: CMOS
Figure 4. Output Filter for PWM Mode
Table 3. Filter Component Selection
MAX98400A/B
C3
L1
L2
C2
C1
C5
R2
C4
R1
RL (I)
L1, L2 (h)
C1 (F)
C2, C3 (F)
C4, C5 (F)
R1, R2 (I)
4
10
0.47
0.10
0.22
10
8
15
0.15
15
16
33
0.10
33
相關PDF資料 |
PDF描述 |
|---|---|
| RCC12DREH-S93 | CONN EDGECARD 24POS .100 EYELET |
| EEM36DRYS | CONN EDGECARD 72POS DIP .156 SLD |
| H2PXH-1636M | DIP CABLE - HDP16H/AE16M/X |
| EMM11DRUS | CONN EDGECARD 22POS DIP .156 SLD |
| ESM08DRTF | CONN EDGECARD 16POS DIP .156 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX98400BEVKIT+ | 功能描述:放大器 IC 開發工具 MAX98400B Eval Kit RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
| MAX98400ETX+ | 制造商:Maxim Integrated Products 功能描述:STEREO CLASS D AMPLIFIER - Rail/Tube |
| MAX98400EVKIT+ | 制造商:Maxim Integrated Products 功能描述:STEREO 6W HIGH POWER CLASS D AMPLIFIER - Boxed Product (Development Kits) |
| MAX9840AEWL+T | 制造商:Maxim Integrated Products 功能描述:MONO 2W CLASS D AMPLIFIER - Tape and Reel |
| MAX984CPE | 功能描述:校驗器 IC RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。