- 您現在的位置：買賣IC網 > PDF目錄371013 > MC14503BCP (MOTOROLA INC) Full Featured -48V Hot Swap Power Manager, Industrial Temp. 14-TSSOP -40 to 85 PDF資料下載
參數資料
| 型號： | MC14503BCP |
| 廠商： | MOTOROLA INC |
| 元件分類： | 通用總線功能 |
| 英文描述： | Full Featured -48V Hot Swap Power Manager, Industrial Temp. 14-TSSOP -40 to 85 |
| 中文描述： | 4000/14000/40000 SERIES, 6-BIT DRIVER, TRUE OUTPUT, PDIP16 |
| 封裝： | PLASTIC, DIP-16 |
| 文件頁數： | 1/6頁 |
| 文件大小： | 211K |
| 代理商： | MC14503BCP |
MOTOROLA CMOS LOGIC DATA
MC14503B
326
The MC14503B is a hex non–inverting buffer with 3–state outputs, and a
high current source and sink capability. The 3–state outputs make it useful in
common bussing applications. Two disable controls are provided. A high
level on the Disable A input causes the outputs of buffers 1 through 4 to go
into a high impedance state and a high level on the Disable B input causes
the outputs of buffers 5 and 6 to go into a high impedance state.
3–State Outputs
TTL Compatible — Will Drive One TTL Load Over Full Temperature
Range
Supply Voltage Range = 3.0 Vdc to 18 Vdc
* Maximum Ratings are those values beyond which damage to the device may occur.
Plastic “P and D/DW” Packages: – 7.0 mW/ C From 65 C To 125 C
Ceramic “L” Packages: – 12 mW/ C From 100 C To 125 C
Storage Temperature
– 65 to + 150
C
Lead Temperature (8–Second Soldering)
260
C
CIRCUIT DIAGRAM
*INn
*DISABLE
*
INPUT
TO OTHER BUFFERS
VSS
VDD
OUTn
* Diode protection on all inputs (not shown)
ONE OF TWO/FOUR BUFFERS
This device contains protection circuitry to guard against damage
due to high static voltages or electric fields. However, precautions must
be taken to avoid applications of any voltage higher than maximum rated
voltages to this high-impedance circuit. For proper operation, Vin and
Vout should be constrained to the range VSS
≤
(Vin or Vout)
≤
VDD.
Unused inputs must always be tied to an appropriate logic voltage
level (e.g., either VSS or VDD). Unused outputs must be left open.
SEMICONDUCTOR TECHNICAL DATA
REV 3
1/94
L SUFFIX
CERAMIC
CASE 620
ORDERING INFORMATION
MC14XXXBCP
MC14XXXBCL
MC14XXXBD
TA = – 55
°
to 125
°
C for all packages.
P SUFFIX
PLASTIC
CASE 648
D SUFFIX
SOIC
CASE 751B
LOGIC DIAGRAM
Plastic
Ceramic
SOIC
TRUTH TABLE
Appropriate
Disable
Input
Inn
0
1
X
Outn
0
1
High
0
0
1
Impedance
X = Don’t Care
DISABLE B
OUT 5
15
12
14
2
4
6
10
1
IN 5
IN 6
IN 1
IN 2
IN 3
IN 4
DISABLE A
OUT 6
OUT 1
OUT 2
OUT 3
OUT 4
11
13
3
5
7
9
VDD = PIN 16
VSS = PIN 8
相關PDF資料 |
PDF描述 |
|---|---|
| MC14503 | Hex Non-Inverting 3-State Buffer |
| MC14503BCL | Hex Non-Inverting 3-State Buffer |
| MC14503BD | Full Featured -48V Hot Swap Power Manager, Industrial Temp. 14-TSSOP -40 to 85 |
| MC145040DW2 | Full Featured -48V Hot Swap Power Manager, Industrial Temp. 44-TSSOP -40 to 85 |
| MC145040 | 8-Bit A/D Converters With Serial Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC14503BCPDS | 制造商:Motorola Inc 功能描述: |
| MC14503BCPG | 功能描述:緩沖器和線路驅動器 3-18V Hex 3-State Non-Inverting RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| MC14503BD | 功能描述:緩沖器和線路驅動器 3-18V Hex 3-State RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| MC14503BDG | 功能描述:緩沖器和線路驅動器 3-18V Hex 3-State Non-Inverting RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| MC14503BDR2 | 功能描述:緩沖器和線路驅動器 3-18V Hex 3-State RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。