- 您現在的位置：買賣IC網 > PDF目錄382301 > MC2300 (Electronic Theatre Controls, Inc.) Navigator Motion Processor PDF資料下載
參數資料
| 型號： | MC2300 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Navigator Motion Processor |
| 中文描述： | 導航運動處理器 |
| 文件頁數： | 35/59頁 |
| 文件大小： | 1925K |
| 代理商： | MC2300 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
MC2300 Technical Specifications
35
CP chip
Pin Name and
number
Addr0
Addr1
Addr2
Addr3
Addr4
Addr5
Addr6
Addr7
Addr8
Addr9
Addr10
Addr11
Addr12
Addr13
Addr14
Addr15
I/OClk
Direction
Description
110
111
112
114
115
116
117
118
119
122
123
124
125
126
127
128
58
output
Multi-purpose Address lines. These pins comprise the CP chip’s external address
bus, used to select devices for communication over the data bus.
Addr0
,
Addr1
,
and
Addr15
are connected to the corresponding
CPAddr
pins on the I/O chip,
and are used to communicate between the CP and I/O chips.
Other address pins may be used for DAC output, parallel word input, or user-
defined I/O operations. See the
Navigator Motion Processor User’s Guide
for a
complete memory map.
input
This is the CP chip clock signal. It should be connected to I/O chip pin 24,
CPClk
.
CP chip analog power supply voltage. This pin must be connected to the analog
input supply voltage, which must be in the range 4.5-5.5 V
If the analog input circuitry is not used, this pin may be left unconnected.
CP chip analog high voltage reference for A/D input. The allowed range is
AnalogRefLow
to
AnalogVcc
.
If the analog input circuitry is not used, this pin may be left unconnected.
CP chip analog low voltage reference for A/D input. The allowed range is
AnalogGND
to
AnalogRefHigh
.
If the analog input circuitry is not used, this pin may be left unconnected.
CP chip analog input ground. This pin must be connected to the analog input
power supply return.
If the analog input circuitry is not used, this pin may be left unconnected.
These signals provide general-purpose analog voltage levels which are sampled
by an internal A/D converter. The A/D resolution is 10 bits.
The allowed range is
AnalogRefLow
to
AnalogRefHigh
.
AnalogVcc
84
input
AnalogRefHigh 85
input
AnalogRefLow 86
input
AnalogGND
87
Analog1
Analog2
Analog3
Analog4
Analog5
Analog6
Analog7
Analog8
PosLim1
PosLim2
PosLim4
74
89
75
88
76
83
77
82
63
65
49
input
input
These signals provide inputs from the positive-side (forward) travel limit
switches. On power-up or
Reset
these signals default to active
low
interpretation,
but the interpretation can be set explicitly using the
SetSignalSense
instruction.
For MC2340 all 4 pins are valid. For MC2320 only
PosLim1
and
PosLim2
are
valid. For MC2310 only
PosLim1
is valid.
WARNING! If a valid axis pin is not used, its signal must be tied
high. PosLim2 is an output during device reset and as such any
connection to GND or V
cc
must be via a series resistor.
Invalid axis pins may also be left unconnected.
相關PDF資料 |
PDF描述 |
|---|---|
| MC26LS30 | Dual Differential Quad Single-Ended (EIA-423-A) Line Drivers |
| MC26LS30D | CABLE GLAND, PG29 |
| MC26LS30DR2 | Dual Differential Quad Single-Ended (EIA-423-A) Line Drivers |
| MC28B | 28 Lead Ceramic Small Outline Package, EPROM NS Package |
| MC33060ADG | Fixed Frequency, PWM, Voltage Mode Single Ended Controllers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC2307 | 制造商:MA-COM 制造商全稱:M/A-COM Technology Solutions, Inc. 功能描述:Open Carrier Double-Balanced Mixer For Microwave Telecommunications |
| MC2307-2 | 制造商:MA-COM 制造商全稱:M/A-COM Technology Solutions, Inc. 功能描述:Open Carrier Double-Balanced Mixer For Microwave Telecommunications |
| MC230B | 制造商:Panasonic Industrial Company 功能描述:BELT MC-230B PANASONIC |
| MC-230B | 制造商:Panasonic Industrial Company 功能描述:BELT |
| MC2310 | 制造商:M/A-COM Technology Solutions 功能描述:RF MIXER 制造商:M/A-COM Technology Solutions 功能描述:Up/Down Conv Mixer 7GHz 4-Pin |
發布緊急采購，3分鐘左右您將得到回復。