欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號： MC28U128HACA-0QC00
廠商： SAMSUNG SEMICONDUCTOR CO. LTD.
英文描述： MultiMediaCard Specification
中文描述： 多媒體卡規格
文件頁數： 31/66頁
文件大?。?/td> 1422K
代理商： MC28U128HACA-0QC00
MultiMediaCard
TM
31
Class 0 is mandatory and supported by all cards. It represents the card identification and initialization
commands, which are intended to handle different cards and card types on the same bus lines. The
Card Command Class (CCC) is coded in the card specific data register of each card, so that the host
knows how to access the card. There are four kinds of commands defined on the MultiMediaCard bus:
-
broadcast commands (bc) sent on CMD line, no response.
-
broadcast commands with response (bcr) sent on CMD line, response (all cards simultaneously) on
CMD line
-
addressed (point-to-point) commands (ac) sent on CMD line, response on CMD line.
-
addressed (point-to-point) data transfer commands (adtc) sent on CMD line, response on CMD line,
data transfer on DAT line.
The command transmission always starts with the MSB. Each command starts with a start bit and ends
with a CRC command protection field followed by an end bit. The length of each command frame is
fixed to 48 bits (2.4 us at 20 MHz):
0
1
Bit5 …. Bit0
Bit31 …. Bit0
Start bit
Host
Command
Argument
Bit6 …. Bit0 1
CRC*1
End Bit
The start bit is always ‘0’ in command frames (sent from host to MultiMediaCard). The host bit is
always ‘1’ for commands. The command field contains the binary coded command number. The
argument depends on the command (refer to Table “Basic Commands (class 0) and Table “Block-
Oriented Read Commands (class 2)”). The CRC field is defined in Chapter “Cyclic Redundancy Check
(CRC)”.
The MultiMediaCard supports the following MultiMediaCard commands :
Table 4-8 Detailed Command Description
CMD
Index
Type
Argument
Resp
CMD0
bc
[31:0] stuff bits
CMD1
bcr
[31:0] OCR
without busy
Abbreviation
GO_IDLE_STATE
SEND_OP_COND
Command description
Resets all card to Idle State
Checks for cards not supporting the full
range of 2.0V to 3.6V. After receiving CMD1
the card sends an R3 response (refer to
Chapter “Responses”).
Asks all cards in ready state to send their
CID
*1
numbers
on CMD-line
Assigns relative address to the card in
identification state.
Programs the DSR of all cards in stand-by
state.
These Samsung MultiMediaCard do not
support this command
Command toggles a card between the
standby and transfer states or between the
programming and disconnect state. In both
cases the card is selected by its own
relative address while deselecting the prior
selected card. Address 0 deselects all.
R3
CMD2
bcr
[31:0] stuff bits R2
ALL_SEND_CID
CMD3
ac
[31:16] RCA
[15:0] stuff bits
[31:16] DSR
[15:0] stuff bits
R1
SET_RELATIVE_A
DDR
SET_DSR
CMD4
bc
CMD7
ac
[31:16] RCA
[15:0] stuff bits
R1 (only
the
select
ed
card)
SELECT/
DESELECT_CARD
CMD8
CMD9
reserved
ac
[31:16] RCA
R2
SEND_CSD
Asks the addressed card to send its card-
相關PDF資料
PDF描述
MC2DU128HACA-0QC00 MultiMediaCard Specification
MC2DU256HACA-0QC00 MultiMediaCard Specification
MC28U016HACA MultiMediaCard Specification
MC28U016NACA MultiMediaCard Specification
MC28U032HACA MultiMediaCard Specification
相關代理商/技術參數
參數描述
MC28U128HACB-0QC00 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification
MC28U128HACC-0QC00 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification
MC28U128HAFA-0QC00 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification
MC28U128HAFB-0QC00 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification
MC28U128HAFC-0QC00 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*
主站蜘蛛池模板： 蓝田县| 五华县| 普陀区| 区。| 色达县| 盖州市| 贵德县| 余姚市| 辉南县| 虹口区| 武夷山市| 肃宁县| 新民市| 崇信县| 裕民县| 新巴尔虎右旗| 墨玉县| 辛集市| 同德县| 鹤岗市| 抚顺县| 理塘县| 天祝| 寿阳县| 翁源县| 云林县| 监利县| 天全县| 翁源县| 淮安市| 陆良县| 林甸县| 龙州县| 阳山县| 灵武市| 津市市| 淳安县| 淮滨县| 静安区| 兴仁县| 南陵县|