欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC33066
廠商: Motorola, Inc.
英文描述: HIGH PERFORMANCE RESONANT MODE CONTROLLERS
中文描述: 高性能諧振模式控制器
文件頁數: 7/12頁
文件大?。?/td> 168K
代理商: MC33066
MC34066 MC33066
7
MOTOROLA ANALOG IC DEVICE DATA
Errors in the threshold voltage and propagation delays
through the output drivers will affect the One–Shot period. To
guarantee accuracy, the output pulse of the control ship is
trimmed to within 5% of 1.5
μ
s with nominal values of RT
and CT.
The outputs of the Oscillator and One–Shot comparators
are OR’d together to produce the pulse ton, which drives the
Flip–Flop and output drivers. The output pulse ton is initiated
by the Oscillator, but either the oscillator comparator or the
One–Shot comparator can terminate the pulse. When the
oscillator discharge time exceeds the one–shot period, the
complete one–shot period is delivered to the output section. If
the oscillator discharge time is less than the one–shot period,
then the oscillator comparator terminates the pulse
prematurely and retriggers the One–Shot. The waveforms on
the left side of Figure 3 correspond to nonretriggered
operation with constant on–time and variable off–times. The
right side of Figure 3 represents retriggered operation with
variable on–time and constant off–time.
Error Amplifier
A fully accessible high performance Error Amplifier is
provided for feedback control of the power supply system.
The Error Amplifier is internally compensated and features dc
open loop gain greater than 70 dB, input offset voltage less
than 10 mV and guaranteed minimum gain–bandwidth
product of 2.5 MHz. The input common mode range extends
from 1.5 V to 5.1 V, which includes the reference voltage. For
common mode voltages below 1.5 V, the Error Amplifier
output is forced low providing minimum oscillator frequency.
The Oscillator Control Current pin is biased by the Error
Amplifier output voltage through RVFO as illustrated in Figure
4. The output swing of the Error Amplifier is restricted by a
clamp circuit to limit the maximum oscillator frequency. The
clamp circuit limits the voltage across RVFO to 2.5 V,
thus limiting IOSC to 2.5 V/RVFO. Oscillator accuracy is
improved by trimming the clamp voltage to obtain the
fOSC(high) specification of 1.0 MHz with nominal value
external components.
Osc Control
Current
3
IOSC
RVFO
Error Amp
Output
Error Amp
Noninverting Input
6
7
Error Amp
Inverting Input
8
Error Amp
Output Clamp
2.5V
EA Clamp
Error
Amplifier
+
+
Figure 4. Error Amplifier and Clamp
Output Section
The pulse, ton, generated by the Oscillator and One–Shot
timer is gated to dual totem pole output drives by the Steering
Flip–Flop shown in Figure 5. Positive transitions of ton toggle
the Flip–Flop, which causes the pulses to alternate between
Output A and Output B. The flip–flop is reset by the
undervoltage lockout circuit during startup to guarantee that
the first pulse appears at Output A.
The totem–pole output drives are ideally suited for driving
power MOSFETs and are capable of sourcing and sinking
1.5 A. Rise and fall times are typically 20 ns when driving a
1.0 nF load. High source/sink capability in a totem–pole
driver normally increases the risk of high cross conduction
current during output transitions. The MC34066 utilizes a
unique design that virtually eliminates cross conduction, thus
controlling the chip power dissipation at high frequencies. A
separate ground terminal is provided for the output drivers to
isolate the sensitive analog circuitry from large
transient currents.
Drivers
Steering
Flip–Flop
ton
T
Q
Q
R
14
12
13
Drive
Output A
Drive
Output B
Drive
Gnd
Fault
UVLO
VCC
Figure 5. Steering Flip–Flop and Output Drivers
PERIPHERAL SUPPORT FUNCTIONS
The MC34066 Resonant Controller provides a number of
support and protection functions including a precision voltage
reference, undervoltage lockout comparators, soft–start
circuitry, and a fault detector. These peripheral circuits ensure
that the power supply can be turned on and off in a safe,
controlled manner and that the system will be quickly
disabled when a fault condition occurs.
Undervoltage Lockout and Voltage Reference
Separate undervoltage lockout comparators sense the
input VCC voltage and the regulated reference voltage as
illustrated in Figure 6. When VCC increases to the upper
threshold voltage, the VCC UVLO comparator enables the
Reference Regulator. After the Vref output of the Reference
Regulator rises to 4.2 V, the Vref UVLO comparator switches
the UVLO signal to a logic zero state enabling the primary
control path. Reducing VCC to the lower threshold voltage
causes the VCC UVLO comparator to disable the Reference
Regulator. The Vref UVLO comparator then switches the
UVLO output to a logic one state disabling the controller.
相關PDF資料
PDF描述
MC34066 HIGH PERFORMANCE RESONANT MODE CONTROLLERS
MC34080 Low Quiescent Current, Programmable-Delay Supervisory Circuit 6-SOT-23 -40 to 125
MC34081BD Low Quiescent Current, Programmable-Delay Supervisory Circuit 6-SOT-23 -40 to 125
MC34081BP Low Quiescent Current, Programmable-Delay Supervisory Circuit 6-SON -40 to 125
MC34080 Low Quiescent Current, Programmable-Delay Supervisory Circuit 6-SOT-23 -40 to 125
相關代理商/技術參數
參數描述
MC33066DW 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HIGH PERFORMANCE RESONANT MODE CONTROLLERS
MC33066P 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:High Performance Resonant Mode Controllers
MC33067 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:High Performance Resonant Mode Controllers
MC33067-34067CN 制造商:未知廠家 制造商全稱:未知廠家 功能描述:中文資料
MC33067DW 功能描述:DC/DC 開關控制器 High Performance RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
主站蜘蛛池模板: 桃源县| 青岛市| 于田县| 开江县| 喀喇沁旗| 浠水县| 盐边县| 桑植县| 姜堰市| 牡丹江市| 喀喇沁旗| 大丰市| 高雄县| 云安县| 滨海县| 公安县| 慈溪市| 康平县| 鄯善县| 罗江县| 宕昌县| 荔浦县| 和田县| 孙吴县| 大新县| 丁青县| 故城县| 安丘市| 信宜市| 阿合奇县| 正镶白旗| 洛宁县| 望江县| 灵山县| 平原县| 林甸县| 房山区| 顺平县| 斗六市| 建阳市| 尤溪县|