欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC33129D
廠商: MOTOROLA INC
元件分類: 穩壓器
英文描述: HIGH PERFORMANCE CURRENT MODE CONTROLLERS
中文描述: 1 A SWITCHING CONTROLLER, 300 kHz SWITCHING FREQ-MAX, PDSO14
封裝: PLASTIC, SO-14
文件頁數: 10/16頁
文件大小: 347K
代理商: MC33129D
MC34129 MC33129
10
MOTOROLA ANALOG IC DEVICE DATA
Fault Timer
This unique circuit prevents sustained operating in a
lockout condition. This can occur with conventional switching
control ICs when operating from a power source with a high
series impedance. If the power required by the load is greater
than that available from the source, the input voltage will
collapse, causing the lockout condition. The Fault Timer
provides automatic recovery when this condition is detected.
Under normal operating conditions, the output of the PWM
Comparator will reset the Latch and discharge the internal
Fault Timer capacitor on a cycle–by–cycle basis. Under
operating conditions where the required power into the load is
greater than that available from the source (Vin), the Ramp
Input voltage (plus offset) will not reach the comparator
threshold level (Pin 11), and the output of the PWM
Comparator will remain low. If this condition persists for more
that 600
μ
s, the Fault Timer will active, discharging CSoft–Start
and initiating a soft–start cycle. The power supply will operate
in a skip cycle or hiccup mode until either the load power or
source impedance is reduced. The minimum fault timeout is
200
μ
s, which limits the useful switching frequency to a
minimum of 5.0 kHz.
Start/Run Comparator
A bootstrap startup circuit is included to improve system
efficiency when operating from a high input voltage. The
output of the Start/Run Comparator controls the state of an
external transistor. A typical application is shown in Figure 21.
While CSoft–Start is charging, startup bias is supplied to VCC
(Pin 14) from Vin through transistor Q2. When
CSoft–Start reaches the 1.95 V clamp level, the Start–Run
output switches low (VCC = 50 mV), turning off Q2. Operating
bias is now derived from the auxiliary bootstrap winding of the
transformer, and all drive power is efficiently converted down
from Vin. The start time must be long enough for the power
supply output to reach regulation. This will ensure that there
is sufficient bias voltage at the auxiliary bootstrap winding for
sustained operation.
tStart =
1.95 V CSoft–Start
1.0
μ
A
= 1.95 CSoft–Start in
μ
F
The Start/Run Comparator has 350 mV of hysteresis. The
output off–state is clamped to VCC + 7.6 V by the internal
zener and PNP transistor base–emitter junction.
Drive Output and Drive Ground
The MC34129 contains a single totem–pole output stage
that was specifically designed for direct drive of power
MOSFETs. It is capable of up to
±
1.0 A peak drive current and
has a typical fall time of 30 ns with a 500 pF load. The
totem–pole stage consists of an NPN transistor for turn–on
drive and a high speed SCR for turn–off. The SCR design
requires less average supply current (ICC) when compared to
conventional switching control ICs that use an all NPN
totem–pole. The SCR accomplishes this during turn–off of
the MOSFET, by utilizing the gate charge as regenerative
on–bias, whereas the conventional all transistor design
requires continuous base current. Conversion efficiency in
low power applications is greatly enhanced with this
reduction of ICC. The SCR’s low–state holding current (IH) is
typically 225
μ
A. An internal 225 k
pull–down resistor is
included to shunt the Drive Output off–state leakage to
ground when the Undervoltage Lockout is active. A separate
Drive Ground is provided to reduce the effects of switching
transient noise imposed on the Ramp Input. This feature
becomes particularly useful when the Ipk(max) clamp level is
reduced. Figure 24 shows the proper implementation of the
MC34129 with a current sensing power MOSFET.
Undervoltage Lockout
The Undervoltage Lockout comparator holds the Drive
Output and CSoft–Start pins in the low state when VCC is less
than 3.6 V. This ensures that the MC34129 is fully functional
before the output stage is enabled and a soft–start cycle
begins. A built–in hysteresis of 350 mV prevents erratic
output behavior as VCC crosses the comparator threshold
voltage. A 14.3 V zener is connected as a shunt regulator
from VCC to ground. Its purpose is to protect the MOSFET
gate from excessive drove voltage during system startup. An
external 9.1 V zener is required when driving low threshold
MOSFETs. Refer to Figure 21. The minimum operating
voltage range of the IC is 4.2 V to 12 V.
References
The 1.25 V bandgap reference is trimmed to
±
2.0%
tolerance at TA = 25
°
C. It is intended to be used in
conjunction with the Error Amp. The 2.50 V reference is
derived from the 1.25 V reference by an internal op amp with
a fixed gain of 2.0. It has an output tolerance of
±
5.0% at TA =
25
°
C and its primary purpose is to supply charging current to
the oscillator timing capacitor.
For further information, please refer to AN976.
相關PDF資料
PDF描述
MC33129P HIGH PERFORMANCE CURRENT MODE CONTROLLERS
MC33129 HIGH PERFORMANCE CURRENT MODE CONTROLLERS
MC34129D HIGH PERFORMANCE CURRENT MODE CONTROLLERS
MC34129P HIGH PERFORMANCE CURRENT MODE CONTROLLERS
MC34164P-3 MICROPOWER UNDERVOLTAGE SENSING CIRCUITS
相關代理商/技術參數
參數描述
MC33129DR2 制造商: 功能描述: 制造商:undefined 功能描述:
MC33129EFR2 功能描述:IC REG CTRLR FLYBK ISO CM 14SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR)
MC33129P 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:High Performance Current Mode Controllers
MC33143 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:DUAL HIGH-SIDE SWITCH
MC33143DW 功能描述:IC SWITCH DUAL H-SIDE 24-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - MOSFET,電橋驅動器 - 內部開關 系列:- 標準包裝:1,000 系列:- 類型:高端/低端驅動器 輸入類型:SPI 輸出數:8 導通狀態電阻:850 毫歐,1.6 歐姆 電流 - 輸出 / 通道:205mA,410mA 電流 - 峰值輸出:500mA,1A 電源電壓:9 V ~ 16 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC(0.295",7.50mm 寬) 供應商設備封裝:PG-DSO-20-45 包裝:帶卷 (TR)
主站蜘蛛池模板: 自治县| 景德镇市| 万年县| 二手房| 富阳市| 封丘县| 揭东县| 清远市| 梁平县| 南丹县| 江达县| 云梦县| 利辛县| 南平市| 五原县| 龙州县| 巴林右旗| 永登县| 盐津县| 鄂伦春自治旗| 遵义市| 金华市| 乐亭县| 浙江省| 万山特区| 修水县| 华宁县| 宝鸡市| 凤阳县| 太康县| 安西县| 林甸县| 沭阳县| 福鼎市| 乾安县| 太康县| 大兴区| 广饶县| 东山县| 正蓝旗| 伊宁县|