- 您現在的位置：買賣IC網 > PDF目錄382303 > MC33461SQ-20CTR (ON SEMICONDUCTOR) Under Voltage Detector Series PDF資料下載
參數資料
| 型號： | MC33461SQ-20CTR |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 電源管理 |
| 英文描述： | Under Voltage Detector Series |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO4 |
| 封裝： | PLASTIC, SC-82AB, 4 PIN |
| 文件頁數： | 11/12頁 |
| 文件大小： | 256K |
| 代理商： | MC33461SQ-20CTR |
MC33460, MC33461
http://onsemi.com
11
INFORMATION FOR USING THE SC–82AB SURFACE MOUNT PACKAGE
MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS
Surface mount board layout is a critical portion of the total
design. The footprint for the semiconductor packages must
be the correct size to insure proper solder connection
interface between the board and the package. With the
correct pad geometry, the packages will self align when
subjected to a solder reflow process.
mm
1.90
0.80
1.30
0.80
SC–82AB
0.60
0.60
0.60
0.80
SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the rated
temperature of the device. When the entire device is heated
to a high temperature, failure to complete soldering within
a short time could result in device failure. Therefore, the
following items should always be observed in order to
minimize the thermal stress to which the devices are
subjected.
Always preheat the device.
The delta temperature between the preheat and
soldering should be 100
°
C or less.*
When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering
method, the difference shall be a maximum of 10
°
C.
The soldering temperature and time shall not exceed
260
°
C for more than 10 seconds.
When shifting from preheating to soldering, the
maximum temperature gradient shall be 5
°
C or less.
After soldering has been completed, the device should
be allowed to cool naturally for at least three minutes.
Gradual cooling should be used as the use of forced
cooling will increase the temperature gradient and
result in latent failure due to mechanical stress.
Mechanical stress or shock should not be applied
during cooling.
* Soldering a device without preheating can cause
excessive thermal shock and stress which can result in
damage to the device.
相關PDF資料 |
PDF描述 |
|---|---|
| MC33461SQ-27CTR | Under Voltage Detector Series |
| MC33461SQ-30CTR | Under Voltage Detector Series |
| MC33461SQ-32CTR | SCREW MACHINE PHIL 6-32X1/4 SS |
| MC33461SQ-43CTR | Under Voltage Detector Series |
| MC33461SQ-45CTR | Under Voltage Detector Series |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33461SQ27CTR | 制造商:ONS 功能描述:ON SEMICONDUCTOR |
| MC33461SQ-27CTR | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| MC33461SQ-30CTR | 制造商:ON Semiconductor 功能描述: |
| MC33461SQ32CTR | 制造商:ONS 功能描述:ON SEMICONDUCTOR NXC7A |
| MC33461SQ-32CTR | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。