欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC34065DWH
廠商: ON SEMICONDUCTOR
英文描述: HIGH PERFORMANCE DUAL CHANNEL CURRENT MODE CONTROLLERS
中文描述: 雙通道電流模式控制器
文件頁數: 6/16頁
文件大小: 419K
代理商: MC34065DWH
MC34065–H, L MC33065–H, L
OPERATING DESCRIPTION
6
MOTOROLA ANALOG IC DEVICE DATA
The MC34065–H,L series are high performance, fixed
frequency, dual channel current mode controllers specifically
designed for Off–Line and dc–to–dc converter applications.
These devices offer the designer a cost effective solution with
minimal external components where independent regulation
of two power converters is required. The Representative
Block Diagram is shown in Figure 15. Each channel contains
a high gain error amplifier, current sensing comparator, pulse
width modulator latch, and totem pole output driver. The
oscillator, reference regulator, and undervoltage lock–out
circuits are common to both channels.
Oscillator
The unique oscillator configuration employed features
precise frequency and duty cycle control. The frequency is
programmed by the values selected for the timing
components RT and CT. Capacitor CT is charged and
discharged by an equal magnitude internal current source
and sink, generating a symmetrical 50 percent duty cycle
waveform at Pin 2. The oscillator peak and valley thresholds
are 3.5 V and 1.6 V respectively. The source/sink current
magnitude is controlled by resistor RT. For proper operation
over temperature it must be in the range of 4.0 k
to 16 k
as
shown in Figure 1.
As CT charges and discharges, an internal blanking pulse
is generated that alternately drives the center inputs of the
upper and lower NOR gates high. This, in conjunction with a
precise amount of delay time introduced into each channel,
produces well defined non–overlapping output duty cycles.
Output 2 is enabled while CT is charging, and Output 1 is
enabled during the discharge. Figure 2 shows the Maximum
Output Duty Cycle versus Oscillator Frequency. Note that
even at 500 kHz, each output is capable of approximately
44% on–time, making this controller suitable for high
frequency power conversion applications.
In many noise sensitive applications it may be desirable to
frequency–lock the converter to an external system clock.
This can be accomplished by applying a clock signal as
shown in Figure 17. For reliable locking, the free–running
oscillator frequency should be set about 10% less than the
clock frequency. Referring to the timing diagram shown in
Figure 16, the rising edge of the clock signal applied to the
Sync input, terminates charging of CT and Drive Output 2
conduction. By tailoring the clock waveform symmetry,
accurate duty cycle clamping of either output can be
achieved. A circuit method for this, and multi–unit
synchronization, is shown in Figure 18.
Error Amplifier
Each channel contains a fully–compensated Error
Amplifier with access to the inverting input and output. The
amplifier features a typical dc voltage gain of 100 dB, and a
unity gain bandwidth of 1.0 MHz with 71
°
of phase margin
(Figure 5). The noninverting input is internally biased at 2.5 V
and is not pinned out. The converter output voltage is
typically divided down and monitored by the inverting input
through a resistor divider. The maximum input bias current is
–1.0
μ
A which will cause an output voltage error that is equal
to the product of the input bias current and the equivalent
input divider source resistance.
The Error Amp output (Pin 5, 12) is provided for external
loop compensation. The output voltage is offset by two diode
drops (
1.4 V) and divided by three before it connects to the
inverting input of the Current Sense Comparator. This
guarantees that no pulses appear at the Drive Output (Pin 7,
10) when the error amplifier output is at its lowest state (VOL).
This occurs when the power supply is operating and the load
is removed, or at the beginning of a soft–start interval
(Figures 20, 21).
The minimum allowable Error Amp feedback resistance is
limited by the amplifier’s source current (0.5 mA) and the
output voltage (VOH) required to reach the comparator’s 1.0 V
clamp level with the inverting input at ground. This condition
happens during initial system startup or when the sensed
output is shorted:
Rf(min)
3.0 (1.0 V)
0.5 mA
1.4 V
= 8800
Current Sense Comparator and PWM Latch
The MC34065 operates as a current mode controller,
whereby output switch conduction is initiated by the oscillator
and terminated when the peak inductor current reaches the
threshold level established by the Error Amplifier output.
Thus the error signal controls the peak inductor current on a
cycle–by–cycle basis. The Current Sense Comparator–PWM
Latch configuration used ensures that only a single pulse
appears at the Drive Output during any given oscillator cycle.
The inductor current is converted to a voltage by inserting a
ground–referenced sense resistor RS in series with the
source of output switch Q1. This voltage is monitored by the
Current Sense Input (Pin 6, 11) and compared to a level
derived from the Error Amp output. The peak inductor current
under normal operating conditions is controlled by the
voltage at Pin 5, 12 where:
V(Pin 5, 12) – 1.4 V
Ipk =
3 RS
Abnormal operating conditions occur when the power
supply output is overloaded or if output voltage sensing is
lost. Under these conditions, the Current Sense Comparator
threshold will be internally clamped to 1.0 V. Therefore the
maximum peak switch current is:
Ipk(max) =
1.0 V
RS
When designing a high power switching regulator it may
be desirable to reduce the internal clamp voltage in order to
keep the power dissipation of RS to a reasonable level. A
simple method to adjust this voltage is shown in Figure 19.
The two external diodes are used to compensate the internal
diodes, yielding a constant clamp voltage over temperature.
Erratic operation due to noise pickup can result if there is an
excessive reduction of the Ipk(max) clamp voltage.
A narrow spike on the leading edge of the current
waveform can usually be observed and may cause the power
supply to exhibit an instability when the output is lightly
loaded. This spike is due to the power transformer
interwinding capacitance and output rectifier recovery time.
The addition of an RC filter on the Current Sense input with a
time constant that approximates the spike duration will
usually eliminate the instability, refer to Figure 24.
相關PDF資料
PDF描述
MC34065P HIGH PERFORMANCE DUAL CHANNEL CURRENT MODE CONTROLLER
MC34065P-H Enhanced Product Single Voltage Detector 5-SC70 -40 to 125
MC34065P-L Automotive Catalog Single Voltage Detectors 5-SC70 -40 to 125
MC34065-H Circular Connector; Body Material:Aluminum; Series:PT06; No. of Contacts:5; Connector Shell Size:14; Connecting Termination:Solder; Circular Shell Style:Straight Plug; Circular Contact Gender:Socket; Insert Arrangement:14-5
MC34065DW-H HIGH PERFORMANCE DUAL CHANNEL CURRENT MODE CONTROLLERS
相關代理商/技術參數
參數描述
MC34065DW-H 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:High Performance Dual Channel Current Mode Controllers
MC34065DW-L 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HIGH PERFORMANCE DUAL CHANNEL CURRENT MODE CONTROLLERS
MC34065-H 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:HIGH PERFORMANCE DUAL CHANNEL CURRENT MODE CONTROLLERS
MC34065-H_06 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:High Performance Dual Channel Current Mode Controllers
MC34065-L 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:High Performance Dual Channel Current Mode Controllers
主站蜘蛛池模板: 开平市| 宝鸡市| 平凉市| 稷山县| 黎平县| 依安县| 翼城县| 丘北县| 临夏市| 原阳县| 祁阳县| 江北区| 新昌县| 汉川市| 临高县| 南阳市| 黔西县| 台江县| 垣曲县| 丁青县| 武定县| 凤城市| 肥城市| 蓬莱市| 定南县| 通渭县| 黔东| 清丰县| 陇南市| 北票市| 青铜峡市| 门源| 保德县| 南宫市| 虎林市| 股票| 五指山市| 延安市| 肥乡县| 县级市| 定日县|