- 您現在的位置：買賣IC網 > PDF目錄382305 > MC3PHAC (Motorola, Inc.) 3-Phase AC Motor Controller PDF資料下載
參數資料
| 型號： | MC3PHAC |
| 廠商： | Motorola, Inc. |
| 英文描述： | 3-Phase AC Motor Controller |
| 中文描述： | 三相交流電機控制器 |
| 文件頁數： | 18/44頁 |
| 文件大小： | 724K |
| 代理商： | MC3PHAC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
MC3PHAC/D
18
3-Phase AC Motor Controller
MOTOROLA
Regeneration Control
— Regeneration is a process by which stored
mechanical energy in the motor and load is transferred back into the
drive electronics, usually as a result of an aggressive deceleration
operation. In special cases where this process occurs frequently (for
example, elevator motor control systems), it is economical to incorporate
special features in the motor drive to allow this energy to be supplied
back to the ac mains. However, for most low cost ac drives, this energy
is stored in the dc bus capacitor by increasing its voltage. If this process
is left unchecked, the dc bus voltage can rise to dangerous levels, which
can destroy the bus capacitor or the transistors in the power inverter.
The MC3PHAC incorporates two techniques to deal with regeneration
before it becomes a problem:
–
Resistive Braking — The DC_BUS pin is monitored at a
5.3 kHz frequency (4.0 kHz when the PWM frequency is set to
15.9 kHz), and when the voltage reaches a certain threshold, the
RBRAKE
pin is driven high. This signal can be used to control a
resistive brake placed across the dc bus capacitor, such that
mechanical energy from the motor will be dissipated as heat in the
resistor versus being stored as voltage on the capacitor. In
standalone mode, the DC_BUS threshold required to assert the
RBRAKE signal is fixed at 3.85 volts (110 percent of nominal) where
nominal is defined to be 3.5 volts. In PC master software mode, this
threshold can be set to any value between 0 volts (0 percent of
nominal) and greater than 5 volts (143 percent of nominal) and can
be changed at any time.
–
Automatic Deceleration Control — When decelerating the motor, the
MC3PHAC attempts to use the specified acceleration value for
deceleration as well. If the voltage on the DC_BUS pin reaches a
certain threshold, the MC3PHAC begins to moderate the
deceleration as a function of this voltage, as shown in
Figure 7
. The
voltage range on the DC_BUS pin from when the deceleration
begins to decrease, to when it reaches 0, is 0.62 volts. In standalone
mode, the DC_BUS voltage where deceleration begins to decrease
is fixed at 3.85 volts (110 percent of nominal) where nominal is
defined to be 3.5 volts. In PC master software mode, this threshold
can be set to any value between 0 volts (0 percent of nominal) and
greater than 5 volts (143 percent of nominal) and can be changed at
any time.
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC3PHACVDW | 3-Phase AC Motor Controller |
| MC3PHACVFA | 3-Phase AC Motor Controller |
| MC3PHACVP | 3-Phase AC Motor Controller |
| MC3S12C128 | 16-Bit Microcontroller |
| MC3S12C32 | 16-Bit Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC3PHACVDW | 功能描述:IC MOTOR CONTROLLER 28-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 標準包裝:1 系列:- 應用:直流電機驅動器，步進電機驅動器 評估套件:- 輸出數:1 或 2 電流 - 輸出:750mA 電壓 - 負載:10 V ~ 40 V 電源電壓:4.5 V ~ 5.5 V 工作溫度:-20°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-BFSOP（0.295"，7.50mm 寬） 供應商設備封裝:24-SOP 包裝:Digi-Reel® 其它名稱:MTS62C19A-HS105DKR |
| MC3PHACVDWE | 功能描述:馬達/運動/點火控制器和驅動器 8BIT MCU 8K FLASH OTP RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MC3PHACVFA | 制造商:Freescale Semiconductor 功能描述:MCU 8BIT HC08 CISC 8KB FLASH 5V 32LQFP - Trays 制造商:Rochester Electronics LLC 功能描述:8BIT MCU, 8K FLASH OTP - Bulk |
| MC3PHACVFAE | 功能描述:馬達/運動/點火控制器和驅動器 8B MCU 8K FLASH OTP RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MC3PHACVP | 制造商:Freescale Semiconductor 功能描述:MCU 8BIT HC08 CISC 8KB FLASH 5V 28PDIP - Rail/Tube 制造商:Freescale Semiconductor 功能描述:Controller IC |
發布緊急采購，3分鐘左右您將得到回復。