欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC68HC11K0CFN2
廠商: MOTOROLA INC
元件分類: 微控制器/微處理器
英文描述: 8-BIT MICROCONTROLLER
中文描述: 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQCC84
封裝: PLASTIC, LCC-84
文件頁數: 22/80頁
文件大小: 420K
代理商: MC68HC11K0CFN2
MOTOROLA
22
M68HC11 K Series
MC6HC11KTS/D
3.4 EEPROM
The 640-byte EEPROM is initially located at $0D80 after reset, assuming EEPROM is enabled in the
memory map by the EEON bit in the CONFIG register. EEPROM can be placed at any 4-Kbyte bound-
ary ($xD80) by writing appropriate values to the INIT2 register. Note that EEPROM can be mapped so
that it contains the vector space. Refer to
Figure 4
. The MC68HC11K0, MC68HC11K3, MC68L11K0,
and MC68L11K3 have no EEPROM. Refer to the
ordering information tables
.
Programming and erasing the EEPROM is controlled by the PPROG register, and dependent upon the
block protect (BPROT) register value. An on-chip charge pump develops the high voltage required for
programming and erasing. When the frequency of the E clock is less than 1 MHz, select the internal
clock source to drive the EEPROM charge pump by writing one to the CSEL bit in the OPTION register.
The CONFIG register consists of a single EEPROM byte. Although the byte is not included in the 640-
byte EEPROM array, programming the CONFIG register requires the same procedure as any byte in
the array. The erased state of bits in the CONFIG register is logic one. Refer to the CONFIG register
description that follows this section.
The erased state of an EEPROM byte is $FF (all ones).
To erase the EEPROM, ensure that the proper bits of the BPROT register are cleared, then complete
the following steps using the PPROG register:
1.
2.
Set the ERASE, EELAT, and appropriate BYTE and ROW bits in PPROG register.
Write to the appropriate EEPROM address with any data. Row erase only requires a write to
any location in the row. Bulk erase is done by writing to any location in the array.
Set the ERASE, EELAT, EEPGM, and appropriate BYTE and ROW bits in PPROG register.
Delay for 10 ms or more, as appropriate.
Clear the EEPGM bit in PPROG to turn off the programming voltage.
Clear the PPROG register to reconfigure the EEPROM address and data buses for normal op-
eration.
To program the EEPROM, ensure the proper bits of the BPROT register are cleared and use the
PPROG register to complete the following steps:
3.
4.
5.
6.
1.
2.
3.
4.
5.
6.
Set the EELAT bit in PPROG register.
Write data to the desired address.
Set EEPGM bit in PPROG.
Delay for 10 ms or more, as appropriate.
Clear the EEPGM bit in PPROG to turn off the programming voltage.
Clear the PPROG register to reconfigure the EEPROM address and data buses for normal op-
eration.
CAUTION
Since it is possible to perform other operations while the EEPROM programming/
erase operation is in progress, it is common to start the operation and then return
to the main program until the 10 ms is completed. When the EELAT bit is set at the
beginning of a program/erase operation, the EEPROM is electronically removed
from the memory map; thus, it is not accessible during the program/erase cycle.
Care must be taken to ensure that EEPROM resources will not be needed by any
routines in the code during the 10 ms program/erase time.
PPROG
—EEPROM Programming Control
$003B
Bit 7
6
5
4
3
2
1
Bit 0
ODD
EVEN
LVPI
BYTE
ROW
ERASE
EELAT
EEPGM
RESET:
0
0
0
0
0
0
0
0
相關PDF資料
PDF描述
MC68HC11K0CFN3 8-BIT MICROCONTROLLER
MC68HC11K0CFN4 8-BIT MICROCONTROLLER
MC68HC11K0CFU2 8-BIT MICROCONTROLLER
MC68HC11K0CFU3 8-BIT MICROCONTROLLER
MC68HC11K0CFU4 8-BIT MICROCONTROLLER
相關代理商/技術參數
參數描述
MC68HC11K0CFN3 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-Bit Microcontroller
MC68HC11K0CFN4 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS MICROCONTROLLER UNIT
MC68HC11K0CFNE3 功能描述:8位微控制器 -MCU 8B MCU 768 RAM - EPP RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HC11K0CFNE4 功能描述:8位微控制器 -MCU 8B MCU 768 RAM - EPP RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HC11K0CFU2 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-Bit Microcontroller
主站蜘蛛池模板: 子洲县| 名山县| 社旗县| 南雄市| 滦南县| 辰溪县| 南充市| 中牟县| 万宁市| 揭西县| 景德镇市| 井陉县| 桓仁| 星子县| 策勒县| 天台县| 额敏县| 东台市| 蛟河市| 吉首市| 大名县| 平舆县| 贡嘎县| 嵊泗县| 华蓥市| 深泽县| 故城县| 邵武市| 民权县| 成武县| 巴彦县| 阿巴嘎旗| 海城市| 天台县| 旌德县| 张北县| 仁布县| 黄冈市| 大石桥市| 昭觉县| 夏津县|