欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC68HC705BD3
廠商: Motorola, Inc.
英文描述: 8-Bit Microcontroller Units (MCU).(8位微控制器)
中文描述: 8位微控制器單元(MCU)。(8位微控制器)
文件頁數: 35/112頁
文件大小: 676K
代理商: MC68HC705BD3
MC68HC05BD3
MOTOROLA
4-3
RESETS AND INTERRUPTS
4
Note:
COP time-out is prevented by periodically writing a “0” to bit 0 of address $3FF0.
If the watchdog timer is allowed to time-out, an internal reset is generated to reset the MCU.
Because the internal reset signal is used, the MCU comes out of a COP reset in the same
operating mode it was in when the COP time-out was generated.
The COP reset function is always enabled.
See Section 5.3 for more information on the COP watchdog timer.
4.2
INTERRUPTS
The MCU can be interrupted by different sources – four maskable hardware interrupt and one
non-maskable software interrupt:
External signal on the IRQ pin
Multi-Function Timer (MFT)
M-Bus Interface (MBUS)
Sync Signal Processor (SSP)
Software Interrupt Instruction (SWI)
If the interrupt mask bit (I-bit) of the CCR is set, all maskable interrupts (internal and external) are
disabled. Clearing the I-bit enables interrupts.
Interrupts cause the processor to save the register contents on the stack and to set the interrupt
mask (I-bit) to prevent additional interrupts. The RTI instruction causes the register contents to be
recovered from the stack and normal processing to resume.
Unlike reset, hardware interrupts do not cause the current instruction execution to be halted, but
are considered pending until the current instruction is complete. The current instruction is the one
already fetched and being operated on. When the current instruction is complete, the processor
checks all pending hardware interrupts. If interrupts are not masked (CCR I-bit clear) the
processor proceeds with interrupt processing; otherwise, the next instruction is fetched and
executed.
Table 4-1 shows the relative priority of all the possible interrupt sources.
4.2.1
Non-maskable Software Interrupt (SWI)
The software interrupt (SWI) is an executable instruction and a non-maskable interrupt: it is
execute regardless of the state of the I-bit in the CCR. If the I-bit is zero (interrupt enabled), SWI
is executed after interrupts that were pending when the SWI was fetched, but before interrupts
generated after the SWI was fetched. The SWI interrupt service routine address is specified by
the contents of memory locations $3FFC and $3FFD.
TPG
相關PDF資料
PDF描述
MC68HC05C4 8-Bit Microcontroller Units (MCU).(8位微控制器)
MC68HC05C5 8-Bit Microcontroller Units (MCU).(8位微控制器)
MC68HC05C8A Microcontrollers
MC68HC05C9A 8-Bit Microcontroller(8位微控制器)
MC68HCL05C9A 8-Bit Microcontroller(8位微控制器)
相關代理商/技術參數
參數描述
MC68HC705BD3P 制造商:Motorola 功能描述:MOTOROLA NXC4C
MC68HC705BD7P1 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68HC705C4ACP 制造商:Freescale Semiconductor 功能描述:
MC68HC705C8AB 功能描述:IC MCU 8K OTP 2.1MHZ 42-SDIP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:HC05 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN,SCI,SPI 外圍設備:POR,PWM,溫度傳感器,WDT 輸入/輸出數:21 程序存儲器容量:40KB(20K x 16) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
MC68HC705C8ACB 制造商:Rochester Electronics LLC 功能描述:HCO5 CORE + 8K RAM + EPR - Bulk
主站蜘蛛池模板: 丰县| 广丰县| 富锦市| 巴里| 福鼎市| 剑河县| 滦平县| 盘山县| 徐水县| 阿荣旗| 手机| 秦安县| 梅州市| 扬中市| 玉门市| 稻城县| 沛县| 浦北县| 通辽市| 东兴市| 突泉县| 通化县| 渑池县| 江陵县| 喀喇沁旗| 辉县市| 安多县| 北川| 闸北区| 南乐县| 磐安县| 江阴市| 峨边| 房产| 清新县| 连城县| 陵水| 蓬安县| 洪湖市| 内丘县| 嘉善县|