- 您現在的位置：買賣IC網 > PDF目錄371048 > MC68HCP11A1MP2 (MOTOROLA INC) HCMOS Single-Chip Microcontroller PDF資料下載
參數資料
| 型號： | MC68HCP11A1MP2 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | HCMOS Single-Chip Microcontroller |
| 中文描述： | 8-BIT, 2 MHz, MICROCONTROLLER, PDIP48 |
| 封裝： | DIP-48 |
| 文件頁數： | 41/158頁 |
| 文件大小： | 776K |
| 代理商： | MC68HCP11A1MP2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁
MC68HC11A8
TECHNICAL DATA
PARALLEL I/O
MOTOROLA
4-3
4
4.4.1 Input Handshake Protocol
In the input handshake protocol, port C is a latching input port, STRA is an edge-sen-
sitive latch command from the external system that is driving port C, and STRB is a
“ready” output line controlled by logic in the MCU.
When a “ready” condition is recognized, the external device places data on the port C
lines, then pulses the STRA line. The active edge on the STRA line latches the port C
data into the PORTCL register, sets the STAF flag (optionally causing an interrupt),
and deasserts the STRB line. Deassertion of the STRB line automatically inhibits the
external device from strobing new data into port C. Reading the PORTCL latch register
(independent of clearing the STAF flag) asserts the STRB line, indicating that new
data may now be applied to port C.
The STRB line can be configured (with the PLS control bit) to be a pulse output (pulse
mode) or a static output (interlocked mode).
The port C data direction register bits should be cleared for each line that is to be used
as a latched input line. However, some port C lines can be used as latched inputs with
the input handshake protocol while, at the same time, using some port C lines as static
inputs, and some port C lines as static outputs. The input handshake protocol has no
effect on the use of port C lines as static inputs or as static outputs. Reads of the
PORTC data register always return the static logic level at the port C lines (for lines
configured as inputs). Writes to either the PORTC data register or the alternate latched
port C register (PORTCL) send information to the same port C output register without
affecting the input handshake strobes.
4.4.2 Output Handshake Protocol
In the output handshake protocol, port C is an output port, STRB is a “ready” output,
and STRA is an edge-sensitive acknowledge input signal, used to indicate to the MCU
that the output data has been accepted by the external device. In a variation of this
output handshake protocol, STRA is also used as an output-enable input, as well as
an edge-sensitive acknowledge input.
The MCU places data on the port C output lines and then indicates stable data is avail-
able by asserting the STRB line. The external device then processes the available
data and pulses the STRA line to indicate that new data may be placed on the port C
output lines. The active edge on the STRA line causes the STRB line to be deasserted
and the STAF status flag to be set. In response to the STAF bit being set, the program
transfers new data out of port C as required. Writing data to the PORTCL register
causes the data to appear on port C lines and asserts the STRB line.
There is a variation to the output handshake protocol that allows three-state operation
on port C. It is possible to directly connect this 8-bit parallel port to other three-state
devices with no additional parts.
While the STRA input line is inactive, all port C lines obey the data direction specified
by the data direction register so that lines which are configured as inputs are high im-
pedance. When the STRA line is activated, all port C lines are forced to outputs re-
gardless of the data in the data direction register. Note that in output handshake
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HCP11A1VFN2 | HCMOS Single-Chip Microcontroller |
| MC68HCP11A1VP2 | HCMOS Single-Chip Microcontroller |
| MC68HC11A8VCFN2 | HCMOS Single-Chip Microcontroller |
| MC68HC11A8VCFU2 | HCMOS Single-Chip Microcontroller |
| MC68HC11A1VFU2 | HCMOS Single-Chip Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HCP11E0CP2 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MC68HCP11E0FN | 功能描述:MICROCONTROLLER MCU 8ADC 3MHC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC11 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| MC68HCP11E0FNE | 功能描述:8位微控制器 -MCU 8B MCU 512RAM COP A/D RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MC68HCP11E1CFNE2 | 功能描述:8位微控制器 -MCU 8B MCU 512 BYTES RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MC68HCP11E1CFNE3 | 功能描述:8位微控制器 -MCU 8B MCU 512 BYTES RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。