欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC68HCP11A1VP2
廠商: MOTOROLA INC
元件分類: 微控制器/微處理器
英文描述: HCMOS Single-Chip Microcontroller
中文描述: 8-BIT, 2 MHz, MICROCONTROLLER, PDIP48
封裝: DIP-48
文件頁數: 59/158頁
文件大小: 776K
代理商: MC68HCP11A1VP2
MC68HC11A8
TECHNICAL DATA
SERIAL PERIPHERAL INTERFACE
MOTOROLA
6-1
6
6 SERIAL PERIPHERAL INTERFACE
This section contains a description on the serial peripheral interface (SPI).
6.1 Overview and Features
The serial peripheral interface (SPI) is a synchronous interface which allows several
SPI microcontrollers or SPI-type peripherals to be interconnected. In a serial periph-
eral interface, separate wires (signals) are required for data and clock. In the SPI for-
mat, the clock is not included in the data stream and must be furnished as a separate
signal. The MC68HC11A8 SPI system may be configured either as a master or as a
slave. The SPI contains the following features:
Full Duplex, Three-Wire Synchronous Transfers
Master or Slave Operation
1.5 MHz (Maximum) Master Bit Frequency
3 MHz (Maximum) Slave Bit Frequency
Four Programmable Master Bit Rates
Programmable Clock Polarity and Phase
End-of-Transmission Interrupt Flag
Write Collision Flag Protection
Master-Master Mode Fault Protection
Easily Interfaces to Simple Expansion Parts (PLLs, D/As, Latches, Display Driv-
ers, etc.)
6.2 SPI Signal Descriptions
The four basic SPI signals (MISO, MOSI, SCK, and SS) are discussed in the following
paragraphs. Each signal is described for both the master and slave modes.
Any SPI output line has to have its corresponding data direction register bit set. If this
bit is clear, the line is disconnected from the SPI logic and becomes a general-purpose
input line. Any SPI input line is forced to act as an input regardless of what is in the
corresponding data direction register bit.
6.2.1 Master In Slave Out (MISO)
The MISO line is configured as an input in a master device and as an output in a slave
device. It is one of the two lines that transfer serial data in one direction, with the most
significant bit sent first. The MISO line of a slave device is placed in the high-imped-
ance state if the slave is not selected.
6.2.2 Master Out Slave In (MOSI)
The MOSI line is configured as an output in a master device and as an input in a slave
device. It is one of the two lines that transfer serial data in one direction with the most
significant bit sent first.
相關PDF資料
PDF描述
MC68HC11A8VCFN2 HCMOS Single-Chip Microcontroller
MC68HC11A8VCFU2 HCMOS Single-Chip Microcontroller
MC68HC11A1VFU2 HCMOS Single-Chip Microcontroller
MC68HC11E0CB2 Microcontrollers
MC68S711E9CFN2 Microcontrollers
相關代理商/技術參數
參數描述
MC68HCP11E0CP2 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68HCP11E0FN 功能描述:MICROCONTROLLER MCU 8ADC 3MHC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:HC11 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN,SCI,SPI 外圍設備:POR,PWM,溫度傳感器,WDT 輸入/輸出數:21 程序存儲器容量:40KB(20K x 16) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
MC68HCP11E0FNE 功能描述:8位微控制器 -MCU 8B MCU 512RAM COP A/D RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HCP11E1CFNE2 功能描述:8位微控制器 -MCU 8B MCU 512 BYTES RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HCP11E1CFNE3 功能描述:8位微控制器 -MCU 8B MCU 512 BYTES RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
主站蜘蛛池模板: 涟水县| 长春市| 固原市| 志丹县| 海原县| 习水县| 泰顺县| 珠海市| 普格县| 凯里市| 眉山市| 阳信县| 建宁县| 屏东县| 鄯善县| 高邮市| 奎屯市| 安徽省| 香港 | 梅州市| 库尔勒市| 曲靖市| 元氏县| 济阳县| 绿春县| 长海县| 金门县| 北海市| 定西市| 顺平县| 曲沃县| 伊春市| 通许县| 庆云县| 新安县| 北安市| 汉沽区| 灵台县| 福贡县| 鄂伦春自治旗| 确山县|