欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC74F168D
廠商: MOTOROLA INC
元件分類: 通用總線功能
英文描述: Automotive Catalog Supply Voltage Supervisor w/Watchdog Input and Manual Reset 5-SOT-23 -40 to 125
中文描述: F/FAST SERIES, SYN POSITIVE EDGE TRIGGERED 4-BIT BIDIRECTIONAL DECADE COUNTER, PDSO16
封裝: PLASTIC, SOIC-16
文件頁數: 3/4頁
文件大小: 119K
代理商: MC74F168D
4-84
FAST AND LS TTL DATA
MC54/74F168
MC54/74F169
FUNCTIONAL DESCRIPTION
The F168 and F169 use edge-triggered J-K type flip-flops
and have no constraints on changing the control or data input
signals in either state of the clock. The only requirement is that
the various inputs attain the desired state at least a setup time
before the rising edge of the clock and remain valid for the rec-
ommended hold time thereafter. The parallel load operation
takes precedence over other operations, as indicated in the
Mode Select Table. When PE is LOW, the data on the P0-P3
inputs enters the flip-flops on the next rising edge of the clock.
In order for counting to occur, both CEP and CET must be
LOW and PE must be HIGH; the U/D input then determines
the direction of counting. The Terminal Count (TC) output is
normally HIGH and goes LOW, provided that CET is LOW,
when a counter reaches zero in the Count Down mode or
reaches 9 (15 for the F169) in the Count Up mode. The TC
output state is not a function of the Count Enable Parallel
(CEP) input level. The TC output of the F168 decade counter
can also be LOW in the illegal states 11, 13, and 15, which can
occur when power is turned on or via parallel loading. If an ille-
gal state occurs, the F168 will return to the legitimate se-
quence within two counts. Since the TC signal is derived by
decoding the flip-flop states, there exists the possibility of de-
coding spikes on TC. For this reason the use of TC as a clock
signal is not recommended (see logic equations below).
1) Count Enable = CEP
CET
PE
2) Up: (
F168): TC = Q0
Q1
Q2
Q3
(Up)
CET
(
F169): TC = Q0
Q1
Q2
Q3
(Up)
CET
3) Down: TC = Q0
Q1
Q2
Q3
(Down)
CET
GUARANTEED OPERATING RANGES
Symbol
Parameter
Min
Typ
Max
Unit
VCC
Supply Voltage
54, 74
4.5
5.0
5.5
V
TA
Operating Ambient Temperature Range
54
–55
25
125
°
C
74
0
25
70
IOH
Output Current — High
54, 74
–1.0
mA
IOL
Output Current — Low
54, 74
20
mA
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE
(unless otherwise specified)
Limits
Symbol
Parameter
Min
Typ
Max
Unit
Test Conditions
VIH
Input HIGH Voltage
2.0
V
Guaranteed Input HIGH Voltage for
All Inputs
VIL
Input LOW Voltage
0.8
V
Guaranteed Input LOW Voltage for
All Inputs
VIK
Input Clamp Diode Voltage
–1.2
V
VCC = MIN, IIN = – 18 mA
VOH
Output HIGH Voltage
54, 74
2.5
3.4
V
IOH = – 1.0 mA
VCC = 4.50 V
74
2.7
3.4
V
IOH = – 1.0 mA
VCC = 4.75 V
VOL
Output LOW Voltage
0.35
0.5
V
IOL = 20 mA
VCC = MIN
IIH
Input HIGH Current
20
μ
A
VCC = MAX, VIN = 2.7 V
0.1
mA
VCC = MAX, VIN = 7.0 V
IIL
Input LOW Current
CET
Other Inputs
–1.2
–0.6
mA
VCC = MAX, VIN = 0.5 V
IOS
Output Short Circuit Current (Note 2)
–60
–150
mA
VCC= MAX, VOUT = 0 V
ICC
Power Supply Current
52
mA
VCC = MAX
NOTES:
1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable device type.
2. Not more than one output should be shorted at a time, nor for more than 1 second.
相關PDF資料
PDF描述
MC74F168N Supply Voltage Supervisor w/Watchdog input and manual reset 5-SOT-23 -40 to 85
MC74F169 Supply Voltage Supervisor w/Watchdog input and manual reset 5-SOT-23 -40 to 85
MC74F169D Supply Voltage Supervisor w/Watchdog input and manual reset 5-SOT-23
MC74F169N Supply Voltage Supervisor w/Watchdog input and manual reset 5-SOT-23
MC74F20 DUAL 4-INPUT NAND GATE
相關代理商/技術參數
參數描述
MC74F169 WAF 制造商:ON Semiconductor 功能描述:
MC74F169D 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:ON Semiconductor 功能描述:
MC74F169DR2 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC74F169M 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC74F169N 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:ON Semiconductor 功能描述:
主站蜘蛛池模板: 黎平县| 花莲县| 鄂温| 永靖县| 从化市| 崇信县| 武定县| 翼城县| 安吉县| 大安市| 涿鹿县| 任丘市| 无棣县| 双辽市| 喜德县| 大同市| 西峡县| 西充县| 旅游| 辽宁省| 介休市| 毕节市| 和田市| 鹤壁市| 福州市| 凌海市| 长子县| 余江县| 清镇市| 临澧县| 历史| 浦东新区| 文山县| 咸丰县| 洞头县| 林芝县| 克拉玛依市| 明光市| 英超| 延津县| 麻栗坡县|