欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC74HC4051AN
廠商: ON SEMICONDUCTOR
元件分類: 運動控制電子
英文描述: Analog Multiplexers/Demultiplexers
中文描述: 8-CHANNEL, SGL ENDED MULTIPLEXER, PDIP16
封裝: PLASTIC, DIP-16
文件頁數: 10/15頁
文件大小: 451K
代理商: MC74HC4051AN
MC54/74HC4051 MC74HC4052 MC54/74HC4053
MOTOROLA
High–Speed CMOS Logic Data
DL129 — Rev 6
10
RL
Figure 12. Crosstalk Between Any Two
Switches, Test Set–Up
Figure 13. Power Dissipation Capacitance,
Test Set–Up
Figure 14a. Total Harmonic Distortion, Test Set–Up
Figure 14b. Plot, Harmonic Distortion
0
–10
–20
–30
–40
–50
–100
1.0
2.0
3.125
FREQUENCY (kHz)
d
–60
–70
–80
–90
FUNDAMENTAL FREQUENCY
DEVICE
SOURCE
ON
6
7
8
16
VEE
CL*
*Includes all probe and jig capacitance
OFF
RL
RL
VIS
RL
CL*
VOS
fin
0.1
μ
F
ON/OFF
6
7
8
16
VCC
CHANNEL SELECT
NC
COMMON O/I
OFF/ON
ANALOG I/O
VCC
A
11
VCC
VEE
ON
6
7
8
16
VCC
VEE
0.1
μ
F
CL*
fin
RL
TO
DISTORTION
METER
*Includes all probe and jig capacitance
VOS
VIS
APPLICATIONS INFORMATION
The Channel Select and Enable control pins should be at
VCC or GND logic levels. VCC being recognized as a logic
high and GND being recognized as a logic low. In this exam-
ple:
VCC = +5V = logic high
GND = 0V = logic low
The maximum analog voltage swings are determined by
the supply voltages VCC and VEE. The positive peak analog
voltage should not exceed VCC. Similarly, the negative peak
analog voltage should not go below VEE. In this example, the
difference between VCC and VEE is ten volts. Therefore,
using the configuration of Figure 15, a maximum analog sig-
nal of ten volts peak–to–peak can be controlled. Unused
analog inputs/outputs may be left floating (i.e., not con-
nected). However, tying unused analog inputs and outputs to
VCC or GND through a low value resistor helps minimize
crosstalk and feedthrough noise that may be picked up by an
unused switch.
Although used here, balanced supplies are not a require-
ment. The only constraints on the power supplies are that:
VCC – GND = 2 to 6 volts
VEE – GND = 0 to –6 volts
VCC – VEE = 2 to 12 volts
and VEE
GND
When voltage transients above VCC and/or below VEE are
anticipated on the analog channels, external Germanium or
Schottky diodes (Dx) are recommended as shown in Figure
16. These diodes should be able to absorb the maximum
anticipated current surges during clipping.
相關PDF資料
PDF描述
MC74HC4051D Analog Multiplexers/Demultiplexers
MC74HC4051DT 3-Terminal Positive Adjustable Regulator
MC74HC4051DW 3-Terminal 0.1A Positive Adjustable Regulator
MC74HC4051N 3-Terminal 0.1A Positive Adjustable Regulator; Package: TO-92R; No of Pins: 3; Container: Tape & Reel
MC74HC4052AD Analog Multiplexers/Demultiplexers
相關代理商/技術參數
參數描述
MC74HC4051ANG 功能描述:多路器開關 IC 2-6V ANLG Mux/Demux -55 to 125deg C RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻(最大值):7 Ohms 開啟時間(最大值): 關閉時間(最大值): 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16
MC74HC4051DR2 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC74HC4051DT 制造商: 功能描述: 制造商:undefined 功能描述:
MC74HC4051DTEL 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC74HC4051DTR2 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel
主站蜘蛛池模板: 巧家县| 泾川县| 红桥区| 天长市| 湘潭县| 日照市| 兴文县| 公主岭市| 永清县| 罗甸县| 共和县| 永城市| 呼伦贝尔市| 玛纳斯县| 迁安市| 巨野县| 锡林浩特市| 涡阳县| 安吉县| 富平县| 海原县| 行唐县| 遵化市| 中山市| 榆中县| 大兴区| 北海市| 兴化市| 江山市| 上思县| 永修县| 古浪县| 岳普湖县| 会理县| 城口县| 进贤县| 绿春县| 扬中市| 同仁县| 正蓝旗| 含山县|