- 您現在的位置：買賣IC網 > PDF目錄382316 > MC75174BDW (ON SEMICONDUCTOR) QUAD EIA-485 LINE DRIVERS PDF資料下載
參數資料
| 型號： | MC75174BDW |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 通用總線功能 |
| 英文描述： | QUAD EIA-485 LINE DRIVERS |
| 中文描述： | QUAD LINE DRIVER, PDSO20 |
| 封裝： | PLASTIC, SOIC-20 |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 180K |
| 代理商： | MC75174BDW |
MC75172B MC75174B
9
MOTOROLA ANALOG IC DEVICE DATA
The maximum ambient operating temperature (applicable
to both EIA–485 and EIA–422–A) is listed as 85
°
C. However,
a lower ambient may be required depending on system use
(i.e. specifically how many drivers within a package are used)
and at what current levels they are operating. The maximum
power which may be dissipated within the package is
determined by:
TJmax–TA
RJA
PDmax
R
θ
JA = package thermal resistance (typical
70
°
C/W for the DIP package, 85
°
C/W for SOIC
package);
TJmax = max. operating junction
temperature, and
TA = ambient temperature.
Since the thermal shutdown feature has a trip point of
150
°
C,
±
20
°
C, TJmax is selected to be 130
°
C. The power
dissipated within the package is calculated from:
= {[(VCC – VOH)
IOH] + VOL
IOL)} each driver
=
+ (VCC
ICC)
VCC = the supply voltage;
VOH, VOL are measured or estimated from
Figures 7 to 10;
ICC = the quiescent power supply current
(typical 60 mA).
where:
PD
where:
As indicated in the equation, the first term (in brackets)
must be calculated and summed for each of the four drivers,
while the last term is common to the entire package.
Example 1:TA = 25
°
C, IOL = IOH = 55 mA for each driver,
VCC = 5.0 V, DIP package. How many drivers per package
can be used
Maximum allowable power dissipation is:
PDmax
130
°
C
25
°
C
70
°
C W
1.5 W
Since the power supply current of 60 mA dissipates
300 mW, that leaves 1.2 W (1.5 W – 0.3 W) for the drivers.
From Figures 7 and 9, VOL
1.75 V, and VOH
power dissipated in each driver is:
{(5.0 – 3.85)
0.055} + (1.75
0.055) = 160 mW.
Since each driver dissipates 160 mW, the four drivers per
package could be used in this application
Example 2:TA = 85
°
C, IOL = 27.8 mA, IOH = 20 mA for each
driver, VCC = 5.0 V, SOIC package. How many drivers per
package can be used
Maximum allowable power dissipation is:
130
°
C
85
°
C
85
°
C W
3.85 V. The
PDmax
0.53 W
Since the power supply current of 60 mA dissipates
300 mW, that leaves 230 mW (530 mW – 300 mW) for the
drivers. From Figures 8 and 10 (adjusted for VCC = 5.0 V),
VOL
1.38 V, and VOH
4.27 V. The power dissipated in
each driver is:
{(5.0 – 4.27)
0.020} + (1.38
0.0278) = 53 mW
Since each driver dissipates 53 mW, the use of all four
drivers in a package would be marginal. Options include
reducing the load current, reducing the ambient temperature,
and/or providing a heat sink.
System Requirements
EIA–485 requires each driver to be capable of transmitting
data differentially to at least 32 unit loads, plus an equivalent
DC termination resistance of 60
, over a common mode
voltage of –7.0 to 12 V. A unit load (U.L.), as defined by
EIA–485, is shown in Figure 17.
Figure 17. Unit Load Definition
1.0 mA
V
5.0 V
–3.0 V
–7.0 V
12 V
–0.8 mA
Reprinted from EIA–485, Electronic Industries Association,
Washington,DC.
I
A load current within the shaded regions represents an
impedance of less than one U.L., while a load current of a
magnitude outside the shaded area is greater than one U.L.
A system’s total load is the sum of the unit load equivalents
of each receiver’s input current, and each disabled driver’s
output leakage current. The 60
termination resistance
mentioned above allows for two 120
terminating resistors.
Using the EIA–485 requirements (worst case limits), and
the graphs of Figures 7 and 9, it can be determined that the
maximum current an MC75172B or MC75174B driver will
source or sink is
65 mA.
System Example
An example of a typical EIA–485 system is shown in
Figure 18. In this example, it is assumed each receiver’s input
characteristics correspond to 1.0 U.L. as defined in Figure 17.
Each “off” driver, with a maximum leakage of
±
50
μ
A over the
common mode range, presents a load of
total load for the active driver is therefore 8.3 unit loads, plus
the parallel combination of the two terminating resistors
(60
). It is up to the system software to control the driver
Enable pins to ensure that only one driver is active at any
time.
0.06 U.L. The
Termination Resistors
Transmission line theory states that, in order to preserve
the shape and integrity of a waveform traveling along a cable,
the cable must be terminated in an impedance equal to its
characteristic impedance. In a system such as that depicted
in Figure 18, in which data can travel in both directions, both
physical ends of the cable must be terminated. Stubs, leading
to each receiver and driver, should be as short as possible.
Leaving off the terminations will generally result in
reflections which can have amplitudes of several volts above
VCC or below ground. These overshoots and undershoots
can disrupt the driver and/or receiver operation, create false
data, and in some cases damage components on the bus.
相關PDF資料 |
PDF描述 |
|---|---|
| MC75174 | QUAD EIA-485 LINE DRIVERS |
| MC75174BP | QUAD EIA-485 LINE DRIVERS |
| MC75172B | QUAD EIA-485 LINE DRIVERS |
| MC75172BDW | QUAD EIA-485 LINE DRIVERS |
| MC7660DR2 | Charge Pump DC-to-DC Voltage Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC75174BDWG | 功能描述:RS-485接口IC Quad EIA-485 Line Driver w/3 State Out RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MC75174BDWR2 | 功能描述:RS-485接口IC Quad EIA-485 Line RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MC75174BDWR2G | 功能描述:RS-485接口IC Quad EIA-485 Line Driver w/3 State Out RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MC75174BP | 功能描述:RS-485接口IC Quad EIA-485 Line RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MC75174BPG | 功能描述:RS-485接口IC Quad EIA-485 Line Driver w/3 State Out RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。