- 您現在的位置：買賣IC網 > PDF目錄16755 > MCP6031DM-PTPLS (Microchip Technology)BOARD DEMO MCP6031 PHOTODIODE PDF資料下載
參數資料
| 型號： | MCP6031DM-PTPLS |
| 廠商： | Microchip Technology |
| 文件頁數： | 7/34頁 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO MCP6031 PHOTODIODE |
| 標準包裝： | 1 |
| 系列： | PICtail™ Plus |
| 主要目的： | 接口，傳感器至模數轉換器接口，光電檢測器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | MCP6031 |
| 主要屬性： | 光電流至電壓轉換 |
| 次要屬性： | RC 低通濾波器 |
| 已供物品： | 板，CD |
| 產品目錄頁面： | 681 (CN2011-ZH PDF) |
| 相關產品： | MCP6031T-E/OTDKR-ND - IC OPAMP SNGL 1.8V SOT23-5 MCP6031T-E/OTCT-ND - IC OPAMP SNGL 1.8V SOT23-5 MCP6031T-E/MCTR-ND - IC OPAMP SNGL 1.8V 8DFN MCP6031-E/MC-ND - IC OPAMP SNGL 1.8V 8DFN MCP6031-E/MS-ND - IC OPAMP SNGL 1.8V 8MSOP MCP6031-E/SN-ND - IC OPAMP SNGL 1.8V 8SOIC MCP6031T-E/MSTR-ND - IC OPAMP SNGL 1.8V 8MSOP MCP6031T-E/SNTR-ND - IC OPAMP SNGL 1.8V 8SOIC MCP6031T-E/OTTR-ND - IC OPAMP SNGL 1.8V SOT23-5 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
2008 Microchip Technology Inc.
DS22041B-page 15
MCP6031/2/3/4
4.2
Rail-to-Rail Output
The output voltage range of the MCP6031/2/3/4 op
amps is VSS + 10 mV (minimum) and VDD – 10 mV
(maximum) when RL =50kΩ is connected to VDD/2
more information.
4.3
Output Loads and Battery Life
The MCP6031/2/3/4 op amp family has outstanding
quiescent current, which supports battery-powered
applications. There is minimal quiescent current glitch-
ing when Chip Select (CS) is raised or lowered. This
prevents excessive current draw, and reduced battery
life, when the part is turned off or on.
Heavy resistive loads at the output can cause exces-
sive battery drain. Driving a DC voltage of 2.5V across
a 100 k
Ω load resistor will cause the supply current to
increase by 25 A, depleting the battery 28 times as
fast as IQ (0.9 A, typical) alone.
High frequency signals (fast edge rate) across capaci-
tive loads will also significantly increase supply current.
For instance, a 0.1 F capacitor at the output presents
an AC impedance of 15.9 k
Ω (1/2πfC) to a 100 Hz
sinewave. It can be shown that the average power
drawn from the battery by a 5.0 Vp-p sinewave
(1.77 Vrms), under these conditions, is
EQUATION 4-1:
This will drain the battery about 12 times as fast as IQ
alone.
4.4
Capacitive Loads
Driving large capacitive loads can cause stability
problems for voltage feedback op amps. As the load
capacitance increases, the feedback loop’s phase
margin decreases and the closed-loop bandwidth is
reduced. This produces gain peaking in the frequency
response, with overshoot and ringing in the step
response. While a unity-gain buffer (G = +1) is the most
sensitive to capacitive loads, all gains show the same
general behavior.
When driving large capacitive loads with these op
amps (e.g., > 100 pF when G = +1), a small series
feedback loop’s phase margin (stability) by making the
output load resistive at higher frequencies. The
bandwidth will be generally lower than the bandwidth
with no capacitance load.
FIGURE 4-3:
Output resistor, RISO
stabilizes large capacitive loads.
different capacitive loads and gains. The x-axis is the
normalized load capacitance (CL/GN), where GN is the
circuit's noise gain. For non-inverting gains, GN and the
Signal Gain are equal. For inverting gains, GN is
1+|Signal Gain| (e.g., -1 V/V gives GN = +2 V/V).
FIGURE 4-4:
Recommended RISO values
for Capacitive Loads.
After selecting RISO for your circuit, double-check the
resulting
frequency
response
peaking
and
step
response overshoot. Modify RISO’s value until the
response is reasonable. Bench evaluation and simula-
tions with the MCP6031/2/3/4 SPICE macro model are
very helpful.
4.5
MCP6033 Chip Select
The MCP6033 is a single op amp with Chip Select
(CS). When CS is pulled high, the supply current drops
to 0.4 nA (typical) and flows through the CS pin to VSS.
When this happens, the amplifier output is put into a
high impedance state. By pulling CS low, the amplifier
is enabled. If the CS pin is left floating, the amplifier will
not operate properly. Figure 1-1 shows the output
voltage and supply current response to a CS pulse.
PSupply = (VDD - VSS) (IQ + VL(p-p) f CL )
= (5V)(0.9 A + 5.0Vp-p 100Hz 0.1F)
= 4.5 W + 50 W
VIN
RISO
VOUT
MCP603X
CL
–
+
1000
10000
100000
1000000
1.E-11 1.E-10 1.E-09 1.E-08 1.E-07 1.E-06
Normalized Load Capacitance; CL/GN (F)
Re
co
m
ende
d
R
IS
O
(
)
GN:
1 V/V
2 V/V
≥ 5 V/V
10p
100p
1n
10n
100n
1
1M
100k
10k
1k
相關PDF資料 |
PDF描述 |
|---|---|
| V300B36E150BG2 | CONVERTER MOD DC/DC 36V 150W |
| V48C8E150BL3 | CONVERTER MOD DC/DC 8V 150W |
| ADM00313 | BOARD EVAL LI-ION CHRG MCP73830L |
| V48C8E150BL | CONVERTER MOD DC/DC 8V 150W |
| H8PPH-1618M | DIP CABLE - HDP16H/AE16M/HDP16H |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP6031DM-PTPLS | 制造商:Microchip Technology Inc 功能描述:Operational Amplifier Demo Board |
| MCP6031-E/MC | 功能描述:運算放大器 - 運放 SNGL 18V 10kHz Op Amp E Temp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MCP6031E/MS | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:0.9 uA, High Precision Op Amps |
| MCP6031-E/MS | 功能描述:運算放大器 - 運放 S-1.8V 14kHz Op Amp E temp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MCP6031-E/OT | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:0.9 μA, High Precision Op Amps |
發布緊急采購，3分鐘左右您將得到回復。