- 您現在的位置：買賣IC網 > Datasheet目錄45 > MIC2594-2BM TR (Micrel Inc)IC CTRLR HOT SWAP NEG HV 8-SOIC Datasheet資料下載
參數資料
| 型號： | MIC2594-2BM TR |
| 廠商： | Micrel Inc |
| 文件頁數： | 18/21頁 |
| 文件大小： | 1079K |
| 描述： | IC CTRLR HOT SWAP NEG HV 8-SOIC |
| 標準包裝： | 2,500 |
| 類型： | 熱交換控制器 |
| 應用： | 通用 |
| 內部開關： | 無 |
| 電源電壓： | -19 V ~ -80 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | MIC2594-2BMTR MIC2594-2BMTR-ND |
September 2005
18
M9999-083005
MIC2588/MIC2594
Micrel
PCB Layout Considerations
4-Wire Kelvin Sensing
Because of the low value typically required for the sense
resistor, special care must be used to measure accurately
the voltage drop across it. Specically, the measurement
technique across each R
SENSE
must employ 4-wire Kelvin
sensing. This is simply a means of making sure that any
voltage drops in the power traces connecting to the resistors
are not picked up by the signal conductors measuring the
voltages across the sense resistors.
Figure 8 illustrates how to implement 4-wire Kelvin sensing.
As the gure shows, all the high current in the circuit (from
V
EE
through R
SENSE
, and then to the source of the output
MOSFET) ows directly through the power PCB traces
and R
SENSE
. The voltage drop resulting across R
SENSE
is
sampled in such a way that the high currents through the
power traces will not introduce any parasitic voltage drops
in the sense leads. It is recommended to connect the hot
swap controllers sense leads directly to the sense resistors
metalized contact pads.
Other Layout Considerations
Figure 9 is a suggested PCB layout diagram for the MIC2588/
MIC2594. Many hot swap applications will require load currents
of several amperes. Therefore, the power (V
EE
and Return)
trace widths (W) need to be wide enough to allow the current
to ow while the rise in temperature for a given copper plate
(e.g., 1oz. or 2oz.) is kept to a maximum of 10癈 to 25癈.
The return (or power ground) trace should be the same width
as the positive voltage power traces (input/load) and isolated
from any ground and signal planes so that the controllers
power is common mode. Also, these traces should be as
short as possible in order to minimize the IR drops between
the input and the load.
Finally, the use of plated-through vias will be necessary to
make circuit connections to the power, ground and signal
planes of multi-layer PCBs.
R
SENSE
Power Trace
From V
EE
PCB Track Width:
0.03" per Ampere
using 1oz Cu
Power Trace
To MOSFET Source
Signal Trace
to MIC2588/MIC2594 V
EE
Pin
Signal Trace
to MIC2588/MIC2594 SENSE Pin
Note: Each SENSE lead trace shall be
balanced for best performance with equal
length/equal aspect ratio.
R
SENSE
metalized
contact pads
Figure 8. 4-Wire Kelvin Sense Connections for R
SENSE
C
FDBK
R4
*POWER MOSFET
(TO-263)
W
W
W
Via to the
power (VEE output)
plane
Current Flow
from the Load
Current Flow
to the Load
- DRAWING IS NOT TO SCALE-
*See Table 1 for part numbers and vendors
^R1 placed on bottom side
Power Plane -------- (red)
Ground Plane ------- (black)
Trace width (W) guidelines and additional information given in
"P B L
R
mm n
i n "
i n f h
h
Via to the
bottom side
Via to the
ground plane
*SENSE RESISTOR
(WSR-2 or
WSL2512)
D1
MIC2588-2BM
VDD
DRAIN
GATE
OV
VEE
/PWRGD
UV
SENSE
R
FDBK
R3
R2
^R1
C3
Via to the
Return (VDD)
plane
Via to the
power (VEE output)
plane
GROUND
PAD
C1
Via to the
Return (VDD)
plane
Figure 9. Recommended PCB Layout for Sense Resistor, Power MOSFET, Overvoltage/Undervoltage Resistive
Divider Network, and Timer Capacitors
相關PDF資料 |
PDF描述 |
|---|---|
| MIC2595R-2BM TR | IC CTRLR HOT SWAP NEG HV 14-SOIC |
| MIC280-7BM6 TR | IC SUPERVISOR THERMAL SOT23-6 |
| MIC2800-GFSYML TR | IC REG TRPL BUCK/LINEAR 16MLF |
| MIC281-7BM6 TR | IC SUPERVISOR THERMAL SOT23-6 |
| MIC2810-1JGMYML TR | IC REG TRPL BUCK/LINEAR 16MLF |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC2594-2YM | 功能描述:熱插拔功率分布 Negative Voltage Hot-Swap Controller - Lead Free RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MIC2594-2YM TR | 功能描述:熱插拔功率分布 Negative Voltage Hot-Swap Controller - Lead Free RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MIC2594-2YM-TR | 功能描述:Hot Swap Controller 1 Channel -48V 8-SOIC 制造商:microchip technology 系列:- 包裝:剪切帶（CT） 零件狀態(tài):停產 類型:熱交換控制器 通道數:1 內部開關:無 應用:-48V 特性:故障超時，閉鎖故障 可編程特性:限流，壓擺率，UVLO 電壓 - 電源:-80 V ~ -19 V 電流 - 輸出（最大值）:- 工作溫度:-40°C ~ 85°C 電流 - 電源:3mA 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商器件封裝:8-SOIC 功能引腳:DRAIN，OFF，ON，/PWRGD 標準包裝:1 |
| MIC2595-1BM | 功能描述:IC CTRLR HOT SWAP NEG HV 14-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| MIC2595-1BM TR | 功能描述:IC CTRLR HOT SWAP NEG HV 14-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
發(fā)布緊急采購，3分鐘左右您將得到回復。