欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MMUN2134LT1
廠商: ON SEMICONDUCTOR
元件分類: 小信號晶體管
英文描述: PNP SILICON BIAS RESISTOR TRANSISTOR
中文描述: 100 mA, 50 V, PNP, Si, SMALL SIGNAL TRANSISTOR, TO-236AB
封裝: CASE 318-08, TO-236, 3 PIN
文件頁數: 9/12頁
文件大小: 133K
代理商: MMUN2134LT1
MMUN2111LT1 Series
http://onsemi.com
9
STEP 1
PREHEAT
ZONE 1
RAMP"
STEP 2
VENT
SOAK"
STEP 3
HEATING
ZONES 2 & 5
RAMP"
STEP 4
HEATING
ZONES 3 & 6
SOAK"
STEP 5
HEATING
ZONES 4 & 7
SPIKE"
STEP 6
VENT
STEP 7
COOLING
200
°
C
150
°
C
100
°
C
50
°
C
TIME (3 TO 7 MINUTES TOTAL)
TMAX
SOLDER IS LIQUID FOR
40 TO 80 SECONDS
(DEPENDING ON
MASS OF ASSEMBLY)
205
°
TO 219
°
C
PEAK AT
SOLDER JOINT
DESIRED CURVE FOR LOW
MASS ASSEMBLIES
100
°
C
150
°
C
160
°
C
140
°
C
Figure 23. Typical Solder Heating Profile
DESIRED CURVE FOR HIGH
MASS ASSEMBLIES
170
°
C
For any given circuit board, there will be a group of
control settings that will give the desired heat pattern. The
operator must set temperatures for several heating zones,
and a figure for belt speed. Taken together, these control
settings make up a heating “profile” for that particular
circuit board. On machines controlled by a computer, the
computer remembers these profiles from one operating
session to the next. Figure 7 shows a typical heating profile
for use when soldering a surface mount device to a printed
circuit board. This profile will vary among soldering
systems but it is a good starting point. Factors that can
affect the profile include the type of soldering system in
use, density and types of components on the board, type of
solder used, and the type of board or substrate material
being used. This profile shows temperature versus time.
SOLDER STENCIL GUIDELINES
Prior to placing surface mount components onto a printed
circuit board, solder paste must be applied to the pads. A
solder stencil is required to screen the optimum amount of
solder paste onto the footprint. The stencil is made of brass
or stainless steel with a typical thickness of 0.008 inches.
The stencil opening size for the surface mounted package
should be the same as the pad size on the printed circuit
board, i.e., a 1:1 registration.
TYPICAL SOLDER HEATING PROFILE
The line on the graph shows the actual temperature that
might be experienced on the surface of a test board at or
near a central solder joint. The two profiles are based on a
high density and a low density board. The Vitronics
SMD310 convection/infrared reflow soldering system was
used to generate this profile. The type of solder used was
62/36/2 Tin Lead Silver with a melting point between
177–189
°
C. When this type of furnace is used for solder
reflow work, the circuit boards and solder joints tend to
heat first. The components on the board are then heated by
conduction. The circuit board, because it has a large surface
area, absorbs the thermal energy more efficiently, then
distributes this energy to the components. Because of this
effect, the main body of a component may be up to 30
degrees cooler than the adjacent solder joints.
相關PDF資料
PDF描述
MMUN5233DW1T1 Dual Bias Resistor Trasnsistors
MMVL105GT1 VOLTAGE VARIABLE CAPACITANCE DIODE
MMVL105GT1 Silicon Tuning Diode
MMVL109T1G Silicon Epicap Diodes
MMVL3401T1 CIRCUIT BREAKER HORZ PCB 10A
相關代理商/技術參數
參數描述
MMUN2134LT1G 功能描述:開關晶體管 - 偏壓電阻器 100mA 50V BRT PNP RoHS:否 制造商:ON Semiconductor 配置: 晶體管極性:NPN/PNP 典型輸入電阻器: 典型電阻器比率: 安裝風格:SMD/SMT 封裝 / 箱體: 直流集電極/Base Gain hfe Min:200 mA 最大工作頻率: 集電極—發射極最大電壓 VCEO:50 V 集電極連續電流:150 mA 峰值直流集電極電流: 功率耗散:200 mW 最大工作溫度: 封裝:Reel
MMUN2134LT1G 制造商:ON Semiconductor 功能描述:TRANSISTOR PRE-BIASED PNP 50V 22/47K
MMUN2134LT3 制造商:LRC 制造商全稱:Leshan Radio Company 功能描述:Bias Resistor Transistors
MMUN2134RLT1 制造商:LRC 制造商全稱:Leshan Radio Company 功能描述:Bias Resistor Transistor
MMUN2135LT1G 制造商:ON Semiconductor 功能描述:PNP DIGITAL TRANSISTOR (B - Tape and Reel 制造商:ON Semiconductor 功能描述:Transistors Switching - Resistor Biased PNP DIGITAL TRANSISTOR
主站蜘蛛池模板: 进贤县| 巧家县| 永川市| 罗山县| 芦山县| 光泽县| 绥中县| 那坡县| 高州市| 康乐县| 邵阳市| 东辽县| 灵武市| 大余县| 哈密市| 开封市| 仲巴县| 翁牛特旗| 温泉县| 慈溪市| 泸州市| 偏关县| 东至县| 江山市| 梅州市| 宝兴县| 望城县| 鹤壁市| 鄂州市| 理塘县| 汉川市| 肇源县| 井陉县| 高雄县| 龙里县| 新化县| 巴林左旗| 贵定县| 太和县| 鄯善县| 缙云县|