- 您現在的位置：買賣IC網 > PDF目錄382352 > MTD505 (Electronic Theatre Controls, Inc.) 5 Port 10M/100M Ethernet Switch PDF資料下載
參數資料
| 型號： | MTD505 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 5 Port 10M/100M Ethernet Switch |
| 中文描述： | 5端口10M/100M以太網交換機 |
| 文件頁數： | 9/19頁 |
| 文件大小： | 202K |
| 代理商： | MTD505 |
9/19
MTD505 Revision 1.2 14/04/2000
MTD505
(Preliminary)
MYSON
TECHNOLOGY
3.0 FUNCTIONAL DESCRIPTIONS
The MTD505 is an 5 ports 10/100 Mbps fast Ethernet switch controller. It is a low cost solution for eight
ports fast Ethernet SOHO switch design. No CPU interface is required; After power on reset, MTD505
provide an auto load configuration setting function through a 2 wire serial EEPROM interface to acess
external EEPROM device, and MTD505 can easily be configured to support port_trunking, port_ VLAN,
static entry, 802.3X flow control threshold setting , flooding port assignment ...etc functions. The follow-
ing descriptions are MTD505’s major functional blocks overview.
3.1 Packet store and forwarding
The MTD505 use simple store and forward algorithm as packet switching method. Input packet from
ports will be stored to external memory first, while packet is good for forward (CRC chech ok, 64Bytes <
length < 1518Bytes, not local packets, in the same VLAN group ) , if this packet’s DA hits, than forward
this packet to the destination port, otherwise this packet will be broadcasted.
3.2 Learning and Routing
The MTD505 supports 1K or 8K MAC entries for switching. Dynamic address learning is performed by
each good unicast packet is completely received. The static address learning is achieved by EEPROM
configuration. On the other hand, the routing process is performed whenever the packet’s DA is cap-
tured. If the DA can not get a hit result, the packet is going to switch broadcast or forward to the dedi-
cated port according to the flooding control selction.
3.3 Aging
Only the dynamic address entries are scheduled in the aging machine. If one station does not transmit
any packet for a period of time, the belonging MAC address will be kicked out from the address table.
The aging out time can be program through the EEPROM auto load configuration. (Default value is 300
seconds)
3.4 Buffer Queue Management
The buffer queue manager is implemented to manage the external shared memory (use SDRAM/
SGRAM) for packet buffering. The main function of the buffer queue manager is to maintain the linked
list consists of buffer IDs, which is used to show the corresponding memory address for each incoming
packet. In addition, the buffer queue manager monitors the rested free spaces status of the external
memory, If the packet storage achieve the predefined threshold value, the buffer queue manager will
raise the alarm signal which is used to enable the flow control mechanism for avoiding transmission ID
queue overflow happening. MTD505 provide 802.3x flow control in full duplex mode and back pressure
control in half duplex mode.
3.5 Full Duplex 802.3x Flow Control
In full duplex mode, MTD505 supports the standard flow control defined in IEEE802.3x standard. It
enables the stopping of remote node transmissions via a PAUSE frame information interactoin. When
the “802.3x flow control enable” bit is set during power on reset (LEDDATA[7] pin is external pull_high),
it enables MTD505 supporting 802.3x flow control function in full_duplex mode; When output port buffer
queue’s on_using value reach the initialization setting threshold value (recommended Xon_TH = 74’h
when using 2Mbytes external memory; Xon_TH = 2e’h when using 1Mbytes external memory),
MTD505 will send out a PAUSE packet with pause time equal to FFF to stop the remote node transmis-
sion; When the output port buffer queue’s on_using value reduce to the initialization threshold
value(recommended Xoff_TH = 30’h when using 2Mbytes external memory; Xoff_TH=18’h when using
1Mbytes external memory), MTD505 will also send a PAUSE packet with pause time equal to zero to
inform the remote node to retransmit packet.
相關PDF資料 |
PDF描述 |
|---|---|
| MTV016 | Enhanced On-Screen-Display Controller |
| MTV030 | On-Screen Display with Auto-Sizing Controller |
| MTV112M | 8051 Embedded CRT Monitor Controller Flash Version |
| MTV118 | On-Screen-Display for LCD Monitor |
| MTV121 | Super On-Screen-Display for LCD Monitor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MTD5052N | 功能描述:PHOTO DIODE 525NM B/G CLR TO-18 RoHS:是 類別:傳感器，轉換器 >> 光學 - 光電檢測器 - 光電二極管 系列:- 標準包裝:1 系列:- 波長:850nm 顏色 - 增強型:- 光譜范圍:400nm ~ 1100nm 二極管類型:引腳 nm 下響應率:0.62 A/W @ 850nm 響應時間:5ns 電壓 - (Vr)（最大）:50V 電流 - 暗（標準）:1nA 有效面積:1mm² 視角:150° 工作溫度:-40°C ~ 100°C 封裝/外殼:徑向，5mm 直徑（T 1 3/4） 其它名稱:475-2649-6 |
| MTD5052N-DIG | 制造商:Marktech Optoelectronics 功能描述:PHOTO DIODE 525NM B/G CLR TO-18 |
| MTD5052W | 功能描述:PHOTO DIODE 525NM FLAT CLR TO-18 RoHS:是 類別:傳感器，轉換器 >> 光學 - 光電檢測器 - 光電二極管 系列:- 標準包裝:1 系列:- 波長:850nm 顏色 - 增強型:- 光譜范圍:400nm ~ 1100nm 二極管類型:引腳 nm 下響應率:0.62 A/W @ 850nm 響應時間:5ns 電壓 - (Vr)（最大）:50V 電流 - 暗（標準）:1nA 有效面積:1mm² 視角:150° 工作溫度:-40°C ~ 100°C 封裝/外殼:徑向，5mm 直徑（T 1 3/4） 其它名稱:475-2649-6 |
| MTD5052W-DIG | 制造商:Marktech Optoelectronics 功能描述:PHOTO DIODE 525NM FLAT CLR TO-18 |
| MTD516 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16 Port 10M/100M Ethernet Switch |
發布緊急采購，3分鐘左右您將得到回復。