- 您現在的位置：買賣IC網 > PDF目錄382352 > MUB08A (National Semiconductor Corporation) 1W, Bypass-Capacitor-less Audio Amplifier with Internal Selectable Gain PDF資料下載
參數資料
| 型號： | MUB08A |
| 廠商： | National Semiconductor Corporation |
| 元件分類： | 運動控制電子 |
| 英文描述： | 1W, Bypass-Capacitor-less Audio Amplifier with Internal Selectable Gain |
| 中文描述： | 1W的，旁路電容器的音頻，內置可選增益放大器 |
| 文件頁數： | 13/15頁 |
| 文件大小： | 468K |
| 代理商： | MUB08A |
Application Information
(Continued)
Mono LM4906 Reference Design Boards
Bill of Material
Part Description
Quantity
1
1
1
5
Reference Designator
U1
C1
C2
J1, J2, Input, Output, V
DD
LM4906 Audio Amplifier
Tantalum Capcitor, 1μF
Ceramic Capacitor, 0.39μF
Jumper Header Vertical Mount 2X1 0.100“ spacing
PCB LAYOUT GUIDELINES
This section provides practical guidelines for mixed signal
PCB layout that involves various digital/analog power and
ground traces. Designers should note that these are only
"rule-of-thumb" recommendations and the actual results will
depend heavily on the final layout.
GENERAL MIXED SIGNAL LAYOUT
RECOMMENDATION
Power and Ground Circuits
For 2 layer mixed signal design, it is important to isolate the
digital power and ground trace paths from the analog power
and ground trace paths. Star trace routing techniques (bring-
ing individual traces back to a central point rather than daisy
chaining traces together in a serial manner) can have a
major impact on low level signal performance. Star trace
routing refers to using individual traces to feed power and
ground to each circuit or even device. This technique will
require a greater amount of design time but will not increase
the final price of the board. The only extra parts required will
be some jumpers.
Single-Point Power / Ground Connections
The analog power traces should be connected to the digital
traces through a single point (link). A "Pi-filter" can be helpful
in minimizing High Frequency noise coupling between the
analog and digital sections. It is further recommended to put
digital and analog power traces over the corresponding digi-
tal and analog ground traces to minimize noise coupling.
Placement of Digital and Analog Components
All digital components and high-speed digital signal traces
should be located as far away as possible from analog
components and circuit traces.
Avoiding Typical Design / Layout Problems
Avoid ground loops or running digital and analog traces
parallel to each other (side-by-side) on the same PCB layer.
When traces must cross over each other do it at 90 degrees.
Running digital and analog traces at 90 degrees to each
other from the top to the bottom side as much as possible will
minimize capacitive noise coupling and cross talk.
L
www.national.com
13
相關PDF資料 |
PDF描述 |
|---|---|
| MUBW10-06A7 | Converter - Brake - Inverter Module |
| MUBW10-06A6 | Converter - Brake - Inverter Module (CBI1) |
| MUBW10-12A6 | Converter - Brake - Inverter Module (CBI1) |
| MUBW15-06A6 | Converter - Brake - Inverter Module (CBI1) |
| MUBW20-06A6K | Converter - Brake - Inverter Module |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MUB25-10DZ | 制造商:SMC Corporation of America 功能描述:Cylinder, compact, plate, dbl act, 25mm |
| MUB31DH | 制造商:MICRO-ELECTRONICS 制造商全稱:Micro Electronics 功能描述:LOW CURRENT HIGH EFFICIENCY LED |
| MUB32DH | 制造商:MICRO-ELECTRONICS 制造商全稱:Micro Electronics 功能描述:ULTRA HIGH BRIGHTNESS RED LED LAMP |
| MUB32DH-5 | 制造商:MICRO-ELECTRONICS 制造商全稱:Micro Electronics 功能描述:LOW CURRENT HIGH EFFICIENCY RED LED LAMP |
| MUB450//5PCK | 制造商:PCTEL 功能描述:ANTENNA HARDWARE/ACCESSORY |
發布緊急采購，3分鐘左右您將得到回復。