欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: NAND128W3A0CZB1
廠商: 意法半導體
英文描述: 128 Mbit, 256 Mbit, 512 Mbit, 1 Gbit (x8/x16) 528 Byte/264 Word Page, 1.8V/3V, NAND Flash Memories
中文描述: 128兆,256兆,512兆位,1千兆位(x8/x16)528 Byte/264字的頁面,1.8V/3V,NAND閃存芯片
文件頁數: 25/57頁
文件大小: 410K
代理商: NAND128W3A0CZB1
25/57
NAND128-A, NAND256-A, NAND512-A, NAND01G-A
Page Program
The Page Program operation is the standard oper-
ation to program data to the memory array.
The main area of the memory array is pro-
grammed by page, however partial page program-
ming is allowed where any number of bytes (1 to
528) or words (1 to 264) can be programmed.
The maximum number of consecutive partial page
program operations allowed in the same page is
three. After exceeding this a Block Erase com-
mand must be issued before any further program
operations can take place in that page.
Before starting a Page Program operation a Point-
er operation can be performed to point to the area
to be programmed. Refer to the
Pointer Opera-
tions
section and
Figure 12.
for details.
Each Page Program operation consists of five
steps (see
Figure 17.
):
1.
one bus cycle is required to setup the Page
Program command
2.
four bus cycles are then required to input the
program address (refer to
Table 6.
)
3.
the data is then input (up to 528 Bytes/ 264
Words) and loaded into the Page Buffer
one bus cycle is required to issue the confirm
command to start the P/E/R Controller.
The P/E/R Controller then programs the data
into the array.
Once the program operation has started the Sta-
tus Register can be read using the Read Status
Register command. During program operations
the Status Register will only flag errors for bits set
to '1' that have not been successfully programmed
to '0'.
During the program operation, only the Read Sta-
tus Register and Reset commands will be accept-
ed, all other commands will be ignored.
Once the program operation has completed the P/
E/R Controller bit SR6 is set to ‘1’ and the Ready/
Busy signal goes High.
The device remains in Read Status Register mode
until another valid command is written to the Com-
mand Interface.
4.
5.
Figure 17. Page Program Operation
Note: Before starting a Page Program operation a Pointer operation can be performed. Refer to
Pointer Operations
section for details.
I/O
RB
Address Inputs
SR0
ai07566
Data Input
10h
70h
80h
Page Program
Setup Code
Confirm
Code
Read Status Register
Busy
(Program Busy time)
相關PDF資料
PDF描述
NAND512W4M5CZC5E 256/512Mb/1Gb (x8/x16, 1.8/3V, 528 Byte Page) NAND Flash Memories 256/512Mb (x16/x32, 1.8V) LPSDRAM, MCP
NAND512R4M2CZB5E 256/512Mb/1Gb (x8/x16, 1.8/3V, 528 Byte Page) NAND Flash Memories 256/512Mb (x16/x32, 1.8V) LPSDRAM, MCP
NAND512W3M5BZB5F 256/512Mb/1Gb (x8/x16, 1.8/3V, 528 Byte Page) NAND Flash Memories 256/512Mb (x16/x32, 1.8V) LPSDRAM, MCP
NAS-xxx SEMI-PRECISION POWER WIREWOUND RESISTOR
NASxxx SEMI-PRECISION POWER WIREWOUND RESISTOR
相關代理商/技術參數
參數描述
NAND128W3A2BDI6 制造商:Micron Technology Inc 功能描述:NAND 制造商:Micron Technology Inc 功能描述:NAND - Gel-pak, waffle pack, wafer, diced wafer on film
NAND128W3A2BN6E 功能描述:閃存 NAND 128 MEG RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
NAND128W3A2BN6F 功能描述:閃存 NAND 128 MEG RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
NAND128W3A2BND 制造商:Micron Technology Inc 功能描述:NAND - Trays
NAND128W3A2BWFD 制造商:Micron Technology Inc 功能描述:NAND - Gel-pak, waffle pack, wafer, diced wafer on film
主站蜘蛛池模板: 古浪县| 樟树市| 临颍县| 江阴市| 乐至县| 东源县| 遂平县| 阿拉善左旗| 清远市| 远安县| 三门峡市| 瓦房店市| 清镇市| 漠河县| 加查县| 五大连池市| 富宁县| 绥芬河市| 红河县| 武山县| 文成县| 家居| 六安市| 淮滨县| 张家界市| 精河县| 扎赉特旗| 岱山县| 华安县| 靖江市| 连城县| 肇东市| 富锦市| 陵川县| 九龙城区| 商洛市| 临沭县| 玉屏| 蕲春县| 黄浦区| 富平县|