欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: NAND128W4A0CV6T
廠商: 意法半導體
英文描述: 128 Mbit, 256 Mbit, 512 Mbit, 1 Gbit (x8/x16) 528 Byte/264 Word Page, 1.8V/3V, NAND Flash Memories
中文描述: 128兆,256兆,512兆位,1千兆位(x8/x16)528 Byte/264字的頁面,1.8V/3V,NAND閃存芯片
文件頁數: 25/57頁
文件大小: 410K
代理商: NAND128W4A0CV6T
25/57
NAND128-A, NAND256-A, NAND512-A, NAND01G-A
Page Program
The Page Program operation is the standard oper-
ation to program data to the memory array.
The main area of the memory array is pro-
grammed by page, however partial page program-
ming is allowed where any number of bytes (1 to
528) or words (1 to 264) can be programmed.
The maximum number of consecutive partial page
program operations allowed in the same page is
three. After exceeding this a Block Erase com-
mand must be issued before any further program
operations can take place in that page.
Before starting a Page Program operation a Point-
er operation can be performed to point to the area
to be programmed. Refer to the
Pointer Opera-
tions
section and
Figure 12.
for details.
Each Page Program operation consists of five
steps (see
Figure 17.
):
1.
one bus cycle is required to setup the Page
Program command
2.
four bus cycles are then required to input the
program address (refer to
Table 6.
)
3.
the data is then input (up to 528 Bytes/ 264
Words) and loaded into the Page Buffer
one bus cycle is required to issue the confirm
command to start the P/E/R Controller.
The P/E/R Controller then programs the data
into the array.
Once the program operation has started the Sta-
tus Register can be read using the Read Status
Register command. During program operations
the Status Register will only flag errors for bits set
to '1' that have not been successfully programmed
to '0'.
During the program operation, only the Read Sta-
tus Register and Reset commands will be accept-
ed, all other commands will be ignored.
Once the program operation has completed the P/
E/R Controller bit SR6 is set to ‘1’ and the Ready/
Busy signal goes High.
The device remains in Read Status Register mode
until another valid command is written to the Com-
mand Interface.
4.
5.
Figure 17. Page Program Operation
Note: Before starting a Page Program operation a Pointer operation can be performed. Refer to
Pointer Operations
section for details.
I/O
RB
Address Inputs
SR0
ai07566
Data Input
10h
70h
80h
Page Program
Setup Code
Confirm
Code
Read Status Register
Busy
(Program Busy time)
相關PDF資料
PDF描述
NAND512R3A0BN6E 128 Mbit, 256 Mbit, 512 Mbit, 1 Gbit (x8/x16) 528 Byte/264 Word Page, 1.8V/3V, NAND Flash Memories
NAND512R3A0CZB6T 128 Mbit, 256 Mbit, 512 Mbit, 1 Gbit (x8/x16) 528 Byte/264 Word Page, 1.8V/3V, NAND Flash Memories
NAND512R3A2BZA1F 128 Mbit, 256 Mbit, 512 Mbit, 1 Gbit (x8/x16) 528 Byte/264 Word Page, 1.8V/3V, NAND Flash Memories
NAND512R3A2BZA1T 128 Mbit, 256 Mbit, 512 Mbit, 1 Gbit (x8/x16) 528 Byte/264 Word Page, 1.8V/3V, NAND Flash Memories
NAND512R3A2BZB1E 128 Mbit, 256 Mbit, 512 Mbit, 1 Gbit (x8/x16) 528 Byte/264 Word Page, 1.8V/3V, NAND Flash Memories
相關代理商/技術參數
參數描述
NAND16GAH0HZA5E 制造商:Micron Technology Inc 功能描述:NAND EMMC - Trays
NAND16GAH0HZA5F 制造商:Micron Technology Inc 功能描述:NAND EMMC - Tape and Reel
NAND16GAHAPZO6E 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE - Trays
NAND16GW3B6DPA6E 功能描述:IC FLASH 16GBIT 114LFBGA RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:576 系列:- 格式 - 存儲器:閃存 存儲器類型:閃存 - NAND 存儲容量:512M(64M x 8) 速度:- 接口:并聯 電源電壓:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TFSOP(0.724",18.40mm 寬) 供應商設備封裝:48-TSOP 包裝:托盤 其它名稱:497-5040
NAND16GW3B6DPA6F 功能描述:IC FLASH 16GBIT 114LFBGA RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:576 系列:- 格式 - 存儲器:閃存 存儲器類型:閃存 - NAND 存儲容量:512M(64M x 8) 速度:- 接口:并聯 電源電壓:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TFSOP(0.724",18.40mm 寬) 供應商設備封裝:48-TSOP 包裝:托盤 其它名稱:497-5040
主站蜘蛛池模板: 通道| 阿拉善左旗| 镇巴县| 新巴尔虎右旗| 宁夏| 科技| 衡山县| 邵阳县| 噶尔县| 疏勒县| 三原县| 澎湖县| 钟山县| 绍兴市| 旬阳县| 通山县| 卢龙县| 旺苍县| 吉安市| 鄂温| 柳河县| 盐池县| 石狮市| 乌鲁木齐市| 治县。| 成安县| 绥化市| 义乌市| 延庆县| 临猗县| 方山县| 寿宁县| 汉沽区| 乌鲁木齐县| 思茅市| 丰顺县| 金川县| 洛川县| 同仁县| 宝鸡市| 札达县|