- 您現在的位置：買賣IC網 > PDF目錄361090 > NCP1086D2T-33R4 (ON SEMICONDUCTOR) 1.5 A Adjustable and 3.3 V Fixed Output Linear Regulator PDF資料下載
參數資料
| 型號： | NCP1086D2T-33R4 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 1.5 A Adjustable and 3.3 V Fixed Output Linear Regulator |
| 中文描述： | 3.3 V FIXED POSITIVE LDO REGULATOR, 1.4 V DROPOUT, PSSO3 |
| 封裝： | D2PAK-3 |
| 文件頁數： | 8/14頁 |
| 文件大小： | 102K |
| 代理商： | NCP1086D2T-33R4 |
NCP1086
http://onsemi.com
8
The case is connected to V
OUT
, and electrical isolation
may be required for some applications. Thermal compound
should always be used with high current regulators such as
these.
The thermal characteristics of an IC depend on the
following four factors:
1.
2.
3.
4.
Maximum Ambient Temperature T
A
(
°
C)
Power dissipation P
D
(W)
Maximum junction temperature T
J
(
°
C)
Thermal resistance junction to ambient R
JA
(
°
C/W)
These four are related by the equation
TJ
The maximum ambient temperature and the power
dissipation are determined by the design while the
maximum junction temperature and the thermal resistance
depend on the manufacturer and the package type.
The maximum power dissipation for a regulator is:
TA
PD
R JA
(eq. 1)
PD(max)
{VIN(max)
VOUT(min)}IOUT(max)
VIN(max)IQ
(eq. 2)
where:
V
IN(max)
is the maximum input voltage,
V
OUT(min)
is the minimum output voltage,
I
OUT(max)
is the maximum output current, for the application
I
Q
is the maximum quiescent current at I
OUT(max)
.
A heatsink effectively increases the surface area of the
package to improve the flow of heat away from the IC and
into the surrounding air.
Each material in the heat flow path between the IC and the
outside environment has a thermal resistance. Like series
electrical resistances, these resistances are summed to
determine R
JA
, the total thermal resistance between the
junction and the surrounding air.
1.
Thermal Resistance of the junction to case, R
JC
(
°
C/W)
2.
Thermal Resistance of the case to Heatsink, R
CS
(
°
C/W)
3.
Thermal Resistance of the Heatsink to the ambient
air, R
SA
(
°
C/W)
These are connected by the equation:
R JA
R JC
R CS
R SA
(eq. 3)
The value for R
JA
is calculated using Equation 3 and the
result can be substituted in Equation 1.
The value for R
JC
is 3.5
°
C/W. For a high current
regulator such as the NCP1086 the majority of the heat is
generated in the power transistor section. The value for
R
SA
depends on the heatsink type, while R
CS
depends on
factors such as package type, heatsink interface (is an
insulator and thermal grease used), and the contact area
between the heatsink and the package. Once these
calculations are complete, the maximum permissible value
of R
JA
can be calculated and the proper heatsink selected.
For further discussion on heatsink selection, see application
note
“Thermal
Management,”
AND8036/D via our website at www.onsemi.com.
document
number
相關PDF資料 |
PDF描述 |
|---|---|
| NCP1086D2T-33R4G | 1.5 A Adjustable and 3.3 V Fixed Output Linear Regulator |
| NCP1086D2T-ADJ | 1.5 A Adjustable and 3.3 V Fixed Output Linear Regulator |
| NCP1086D2T-ADJR4 | 1.5 A Adjustable and 3.3 V Fixed Output Linear Regulator |
| NCP1086ST-33T3 | 1.5 A Adjustable and 3.3 V Fixed Output Linear Regulator |
| NCP1086ST-ADJT3 | 0.5mm Pitch DIL Vertical SMT Female Assembly, 2mm height, location pegs, hold-down tabs, tin, 11+11-way, Tape & Reel packing |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP1086D2T-33R4G | 功能描述:低壓差穩壓器 - LDO 3.3V 1.5A Commercial Temp RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| NCP1086D2T-ADJ | 功能描述:低壓差穩壓器 - LDO 1.25-5.5V ADJ 1.5A RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| NCP1086D2T-ADJG | 功能描述:低壓差穩壓器 - LDO ANA 1.5A ADJSTBL REG RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| NCP1086D2T-ADJR4 | 功能描述:低壓差穩壓器 - LDO 1.25-5.5V ADJ 1.5A RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| NCP1086D2TADJR4G | 功能描述:低壓差穩壓器 - LDO 1.25-5.5V ADJ 1.5A Commercial Temp RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。