- 您現在的位置：買賣IC網 > PDF目錄361091 > NCP1395APG (ON SEMICONDUCTOR) High Performance Resonant Mode Controller PDF資料下載
參數資料
| 型號： | NCP1395APG |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 穩壓器 |
| 英文描述： | High Performance Resonant Mode Controller |
| 中文描述： | SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDIP16 |
| 封裝： | LEAD FREE, PLASTIC, DIP-8 |
| 文件頁數： | 22/27頁 |
| 文件大小： | 345K |
| 代理商： | NCP1395APG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁
NCP1395A/B
http://onsemi.com
22
Protection Circuitry
This resonant controller differs from competitors due to
its protection features. The device can react to various
inputs like:
Fast events input:
Like an overcurrent condition, a
need to shutdown (sleep mode) or a way to force a
controlled burst mode (skip cycle at low output
power): as soon as the input level exceeds 1.0 V
typical, pulses are immediately stopped. On the
A version, when the input is released, the controller
performs a clean startup sequence without softstart
unless the feedback voltage goes down below 0.6 V
during fault time (please see above for details). The
B version restarts with a softstart sequence.
Slow events input:
This input serves as a delayed
shutdown, where an event like a transient overload
does not immediately stopped pulses but start a timer.
If the event duration lasts longer than what the timer
imposes, then all pulses are disabled. The voltage on
the timer capacitor (pin 3) starts to decrease until it
reaches 1.0 V. The decrease rate is actually depending
on the resistor the user will put in parallel with the
capacitor, giving another flexibility during design.
Figure 48 depicts the architecture of the fault circuitry.
Vdd
Itimer
Reset
UVLO
Output
Current
Image
Rtimer
Ctimer
Ctimer
NINV
+
ON/OFF
1 = fault
0 = ok
+
Vref Fault
+
+
VtimerON
VtimerOFF
1 = ok
0 = fault
+
Vref Fault
+
+
Vref
Out
CC Regulation
Compensation
Slow Fault
Fast Fault
+
1 = ok
0 = fault
DRIVING
LOGIC
SS
A
A
B
B
Reset
To FB
Fast
Input
Figure 48. This Circuit Combines a Slow and Fast Input for Improved Protection Features
相關PDF資料 |
PDF描述 |
|---|---|
| NCP1395ADR2G | High Performance Resonant Mode Controller |
| NCP1395BDR2G | High Performance Resonant Mode Controller |
| NCP1395BPG | High Performance Resonant Mode Controller |
| NCP1395A | High Performance Resonant Mode Controller(高性能諧振模式控制器) |
| NCP1395B | High Performance Resonant Mode Controller(高性能諧振模式控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP1395B | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:High Performance Resonant Mode Controller |
| NCP1395BDR2G | 功能描述:電壓模式 PWM 控制器 PWM CONTROLLER RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| NCP1395BPG | 功能描述:電壓模式 PWM 控制器 PWM CONTROLLER RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| NCP1395D | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:High Performance Resonant Mode Controller |
| NCP1395LLCGEVB | 功能描述:BOARD EVAL NCP1395 RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓撲結構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
發布緊急采購，3分鐘左右您將得到回復。