- 您現在的位置：買賣IC網 > PDF目錄361092 > NCP1511FCT1G (ON SEMICONDUCTOR) Up to 500 mA, High Efficiency Synchronous Step-Down DC-DC Converter PDF資料下載
參數資料
| 型號： | NCP1511FCT1G |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 穩壓器 |
| 英文描述： | Up to 500 mA, High Efficiency Synchronous Step-Down DC-DC Converter |
| 中文描述： | 0.8 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PBGA9 |
| 封裝： | LEAD FREE, MICRO BUMP-9 |
| 文件頁數： | 13/16頁 |
| 文件大小： | 162K |
| 代理商： | NCP1511FCT1G |
NCP1511
http://onsemi.com
13
PCB Layout Recommendations
Good PCB layout plays an important role in switching
mode power conversion. Careful PCB layout can help to
minimize ground bounce, EMI noise and unwanted feedback
that can affect the performance of the converter. Hints
suggested below can be used as a guideline in most situations.
1. Use starground connection to connect the IC ground
nodes and capacitor GND nodes together at one point.
Keep them as close as possible. And then connect this to the
ground plane through several vias. This will reduce noise
in the ground plane by preventing the switching currents
from flowing through the ground plane.
2. Place the power components (i.e., input capacitor,
inductor and output capacitor) as close together as possible
for best performance. All connecting traces must be short,
direct, and wide to reduce voltage errors caused by resistive
losses through the traces.
3. Separate the feedback path of the output voltage from
the power path. Keep this path close to the NCP1511
circuit. And also route it away from noisy components.
This will prevent noise from coupling into the voltage
feedback trace.
4. Place the DCDC converter away from noise sensitive
circuitry, such as RF circuits.
The following shows the NCP1511 demo board layout
and bill of materials:
Figure 27. Top and Silkscreen Layer
Figure 28. Soldermask Top and Silkscreen Layer
相關PDF資料 |
PDF描述 |
|---|---|
| NCP1521AMUTBG | 1.5 MHz, 600 mA, High−Efficiency, Low Quiescent Current, Adjustable Output Voltage Step−Down Converter |
| NCP1521ASNT1G | 1.5 MHz, 600 mA, High−Efficiency, Low Quiescent Current, Adjustable Output Voltage Step−Down Converter |
| NCP1522ASNT1G | 3.0 MHz, 600 mA, High−Efficiency, Low Quiescent Current, Adjustable Output Voltage Step−Down Converter |
| NCP1523 | 6-A, 2.2-V to 5.5-V INPUT, NON-ISOLATED, WIDE-OUTPUT, ADJUSTABLE POWER MODULE WITH TurboTrans |
| NCP1560 | Full Featured Voltage Mode PWM Controller(全性能電壓模式PWM控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP1521ASNT1G | 功能描述:直流/直流開關轉換器 ANA LED DRIVER RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| NCP1521B | 制造商:ON 功能描述:1.5 MHz, 600 mA Step-Down DC-DC Converter |
| NCP1521BEVB | 功能描述:電源管理IC開發工具 NCP1521B ANA EVAL BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| NCP1521BMUTBG | 功能描述:直流/直流開關轉換器 STEP DWN DCDC CNVRTR 1.5MHz 600mA RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| NCP1521BSNT1G | 功能描述:直流/直流開關轉換器 STEP DWN DCDC CNVRTR 1.5MHz 600mA RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。