- 您現在的位置：買賣IC網 > PDF目錄361092 > NCP1560 (ON SEMICONDUCTOR) Full Featured Voltage Mode PWM Controller(全性能電壓模式PWM控制器) PDF資料下載
參數資料
| 型號： | NCP1560 |
| 廠商： | ON SEMICONDUCTOR |
| 英文描述： | Full Featured Voltage Mode PWM Controller(全性能電壓模式PWM控制器) |
| 中文描述： | 全功能電壓模式PWM控制器（全性能電壓模式的PWM控制器） |
| 文件頁數： | 4/18頁 |
| 文件大小： | 122K |
| 代理商： | NCP1560 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁
NCP1560
http://onsemi.com
4
PIN DESCRIPTION
Pin
Name
Application Information
1
V
in
This pin is connected to the bulk DC input voltage supply. A constant current source supplies current from
this pin to the capacitor connected on the V
AUX
pin. The charge current is typically 13.8 mA. Input voltage
range is 21.5 V to 150 V.
2
UV/OV
Input supply voltage is scaled down and sampled by means of a resistor divider. The supply voltage must
be scaled down between 1.52 V and 3.61 V within the specified input voltage range.
3
NC
Not Connected.
4
FF
An external resistor between V
and this pin adjusts the amplitude of the FF Ramp in proportion to V
. By
varying the feedforward ramp amplitude in proportion to the input voltage, changes in loop bandwidth are
eliminated.
5
CS
Over current sense input. If the CS voltage exceeds 0.48 V or 0.57 V, the converter enters the Cycle by
Cycle or Cycle Skip current limit mode, respectively.
6
CSKIP
The capacitor connected between this pin and ground sets the Cycle Skip period. A soft start sequence
follows at the conclusion of the fault period.
7
R
T
A single external resistor between this pin and GND sets the oscillator fixed frequency.
8
DC
MAX
An external resistor between this pin and GND sets the voltage on the Max DC Comparator inverting in-
put. The duty cycle is limited by comparing the voltage on the Max DC Comparator inverting input to the
Feedforward Ramp.
9
SS
An internal 6.2 A current source charges the external capacitor connected to this pin. The duty cycle is
limited during start-up by comparing the voltage on this pin to the Oscillator Ramp.
10
V
EA
The error signal from an external error amplifier is fed into this input and compared to the Feedforward
Ramp. A series diode and resistor offset the voltage on this pin before it is applied to the PWM Compara-
tor inverting input.
11
V
REF
Precision 5.0 V reference output. Maximum output current is 6 mA.
12
t
D
An external resistor between V
REF
and this pin sets the overlap delay between OUT1 and OUT2 transi-
tions.
13
OUT2
Output of the PWM controller with leading and trailing edge overlap delay. OUT2 can be used to drive a
synchronous rectifier topology, an active clamp/reset switch, or both.
14
GND
Control circuit ground.
15
OUT1
Main output of the PWM controller.
16
V
AUX
Positive input supply voltage. This pin is connected to an external capacitor for energy storage. An inter-
nal current supplies current from V
in
to this pin. Once the voltage on V
AUX
reaches 11 V, the current
source turns OFF. It turns ON again once V
AUX
falls to 7 V. During normal operation, power is supplied to
the IC via this pin, by means of an auxiliary winding.
相關PDF資料 |
PDF描述 |
|---|---|
| NCP1560HDR2 | Quadruple Differential Line Receiver With 3-State Outputs 16-PDIP 0 to 70 |
| NCP1562A | High Performance Active Active Clamp/Reset PWM Controller Controller(高性能有效Clamp/Reset PWM控制器) |
| NCP1562B | High Performance Active Active Clamp/Reset PWM Controller Controller(高性能有效Active Clamp/Reset PWM控制器) |
| NCP1729 | Switched Capacitor Voltage Inverter |
| NCP1729SN35T1 | Switched Capacitor Voltage Inverter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP1560HDR2 | 功能描述:IC REG CTRLR FLYBACK PWM 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| NCP1560HDR2G | 制造商:Rochester Electronics LLC 功能描述: 制造商:ON Semiconductor 功能描述: |
| NCP1561DR2 | 功能描述:直流/直流開關轉換器 Dual Output PWM RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| NCP1561DR2G | 功能描述:直流/直流開關轉換器 Dual Output PWM RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| NCP1562-100WEVBG | 功能描述:電源管理IC開發工具 100 W 48 V TELECOM BRICK RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。