- 您現在的位置：買賣IC網 > Datasheet目錄45 > NCT72CMNR2G (ON Semiconductor)IC REMOTE THERMAL SENSOR 8-DFN Datasheet資料下載
參數資料
| 型號： | NCT72CMNR2G |
| 廠商： | ON Semiconductor |
| 文件頁數： | 8/20頁 |
| 文件大小： | 326K |
| 描述： | IC REMOTE THERMAL SENSOR 8-DFN |
| 標準包裝： | 1 |
| 功能： | 溫度監控系統（傳感器） |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | 0°C ~ 127°C，-64°C ~ 191°C |
| 精確度： | ±2.5°C |
| 拓撲： | ADC，比較器，多路復用器，寄存器庫 |
| 輸出類型： | 2 線串行，I²C?/SMBUS? |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 2.8 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-VFDFN 裸露焊盤 |
| 供應商設備封裝： | 8-DFN（3x3） |
| 包裝： | 標準包裝 |
| 其它名稱： | NCT72CMNR2GOSDKR |
NCT72
http://onsemi.com
8
Figure 14. Input Signal Conditioning
LOW-PASS FILTER
f
C
= 65 kHz
REMOTE
SENSING
TRANSISTOR
BIAS
DIODE
D+
D
V
DD
I
BIAS
I
N1 ?I
V
OUT+
V
OUT
To ADC
N2 ?I
C1*
*CAPACITOR C1 IS OPTIONAL. IT IS ONLY NECESSARY IN NOISY ENVIRONMENTS. C1 = 1,000 pF MAX.
Temperature Measurement Results
The results of the local and remote temperature
measurements are stored in the local and remote temperature
value registers and compared with limits programmed into
the local and remote high and low limit registers.
The local temperature value is in Register 0x00 and has a
resolution of 1癈. The external temperature value is stored
in two registers, with the upper byte in Register 0x01 and the
lower byte in Register 0x10. Only the two MSBs in the
external temperature low byte are used giving the external
temperature measurement a resolution of 0.25癈. Table 6
lists the data format for the external temperature low byte.
Table 6. EXTENDED TEMPERATURE RESOLUTION
(REMOTE TEMPERATURE LOW BYTE)
Extended Resolution
Remote Temperature
Low Byte
0.00癈
0 000 0000
0.25癈
0 100 0000
0.50癈
1 000 0000
0.75癈
1 100 0000
When reading the full external temperature value, read the
LSB first. This causes the MSB to be locked (that is, the
ADC does not write to it) until it is read. This feature ensures
that the results read back from the two registers come from
the same measurement.
Temperature Measurement Range
The temperature measurement range for both internal and
external measurements is, by default, 0癈 to +127癈.
However, the NCT72 can be operated using an extended
temperature range. The extended measurement range is
64癈 to +191癈. Therefore, the NCT72 can be used to
measure the full temperature range of an external diode,
from 55癈 to +150癈.
The extended temperature range is selected by setting
Bit 2 of the configuration register to 1. The temperature
range is 0癈 to 127癈 when Bit 2 equals 0. A valid result is
available in the next measurement cycle after changing the
temperature range.
In extended temperature mode, the upper and lower
temperature that can be measured by the NCT72 is limited
by the remote diode selection. The temperature registers can
have values from 64癈 to +191癈. However, most
temperature sensing diodes have a maximum temperature
range of 55癈 to +150癈. Above +150癈, they may lose
their semiconductor characteristics and approximate
conductors instead. This results in a diode short. In this case,
a read of the temperature result register gives the last good
temperature measurement. Therefore, the temperature
measurement on the external channel may not be accurate
for temperatures that are outside the operating range of the
remote sensor.
It should be noted that although both local and remote
temperature measurements can be made while the part is in
extended temperature mode, the NCT72 itself should not be
exposed to temperatures greater than those specified in the
absolute maximum ratings section. Further, the device is
only guaranteed to operate as specified at ambient
temperatures from 40癈 to +120癈.
Temperature Data Format
The NCT72 has two temperature data formats. When the
temperature measurement range is from 0癈 to 127癈
(default), the temperature data format for both internal and
external temperature results is binary. When the
measurement range is in extended mode, an offset binary
data format is used for both internal and external results.
Temperature values are offset by 64癈 in the offset binary
data format. Examples of temperatures in both data formats
are shown in Table 7.
相關PDF資料 |
PDF描述 |
|---|---|
| NCT7491RQR2G | IC REMOTE THERMAL MONITOR 24QSOP |
| NCT75MNR2G | IC SENSOR TEMP DGTL 8DFN |
| NCV8881PWR2G | IC REG TRPL BUCK/LINEAR 16SOIC |
| NE1617ADS,112 | IC TEMP MONITOR 16SSOP |
| NE1619DS,118 | IC TEMP MONITOR 16SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCT72CMTR2G | 功能描述:板上安裝溫度傳感器 REMOTE THERMAL SENSOR RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| NCT72DMNR2G | 功能描述:板上安裝溫度傳感器 DIGTEMPSEN2WIREINTF RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| NCT72DMTR2G | 功能描述:板上安裝溫度傳感器 DUAL-SUPPLYBI DIRECTIONAL RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| NCT7491MNR2G | 制造商:ON Semiconductor 功能描述:NCT7491 REMOTE THERMAL MO - Bulk |
| NCT7491MNTXG | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。