- 您現在的位置：買賣IC網 > PDF目錄376245 > OP497GP (ANALOG DEVICES INC) Precision Picoampere Input Current Quad Operational Amplifier PDF資料下載
參數資料
| 型號： | OP497GP |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | Precision Picoampere Input Current Quad Operational Amplifier |
| 中文描述： | QUAD OP-AMP, 250 uV OFFSET-MAX, 0.5 MHz BAND WIDTH, PDIP14 |
| 封裝： | PLASTIC, MS-001, DIP-14 |
| 文件頁數： | 7/12頁 |
| 文件大小： | 302K |
| 代理商： | OP497GP |
REV. D
OP497
–7–
APPLICATIONS INFORMATION
Extremely low bias current over the full military temperature range
makes the OP497 attractive for use in sample-and-hold amplifiers,
peak detectors, and log amplifiers that must operate over a wide
temperature range. Balancing input resistances is not necessary
with the OP497. Offset voltage and TCV
OS
are degraded only
minimally by high source resistance, even when unbalanced.
The input pins of the OP497 are protected against large differen-
tial voltage by back-to-back diodes and current-limiting resistors.
Common-mode voltages at the inputs are not restricted, and may
vary over the full range of the supply voltages used.
The OP497 requires very little operating headroom about the
supply rails, and is specified for operation with supplies as low
as
±
2 V. Typically, the common-mode range extends to within
1 V of either rail. The output typically swings to within 1 V of
the rails when using a 10 k
load.
AC PERFORMANCE
The OP497’s ac characteristics are highly stable over its full
operating temperature range. Unity-gain small-signal response is
shown in Figure 1. Extremely tolerant of capacitive loading on
the output, the OP497 displays excellent response even with
1000 pF loads (Figure 2).
10
0%
90
100
20mV
5 s
Figure 1. Small-Signal Transient Response
(C
LOAD
= 100 pF, A
VCL
= 1)
10
0%
90
100
20MV
5 s
Figure 2. Small-Signal Transient Response
(C
LOAD
= 1000 pF, A
VCL
= 1)
10
0%
90
100
2V
50 s
Figure 3. Large-Signal Transient Response (A
VCL
= 1)
GUARDING AND SHIELDING
To maintain the extremely high input impedances of the OP497,
care must be taken in circuit board layout and manufacturing.
Board surfaces must be kept scrupulously clean and free of mois-
ture. Conformal coating is recommended to provide a humidity
barrier. Even a clean PC board can have 100 pA of leakage currents
between adjacent traces, so guard rings should be used around
the inputs. Guard traces are operated at a voltage close to that
on the inputs, as shown in Figure 4, so that leakage currents
become minimal. In noninverting applications, the guard ring
should be connected to the common-mode voltage at the invert-
ing input. In inverting applications, both inputs remain at ground,
so the guard trace should be grounded. Guard traces should be
on both sides of the circuit board.
1/4
OP497
+
UNITY GAIN FOLLOWER
NONINVERTING AMPLIFIER
INVERTING AMPLIFIER
B
8
A
1
MINI-DIP
BOTTOM VIEW
–
+
–
–
+
1/4
OP497
1/4
OP497
Figure 4. Guard Ring Layout and Connections
相關PDF資料 |
PDF描述 |
|---|---|
| op497 | Input Current Quad OP AMP(微微安培輸入電流四運放) |
| OP50 | High Output Current Operational Amplifier |
| OP-50 | High Output Current Operational Amplifier |
| OP-50A | High Output Current Operational Amplifier |
| OP-50B | High Output Current Operational Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OP-497GP | 制造商:AD 制造商全稱:Analog Devices 功能描述:PRECISION PICOAMPERE INPUT CURRENT QUAD OPERATIONAL AMPLIFIER |
| OP497GP | 制造商:Analog Devices 功能描述:SEMICONDUCTORSLINEAR |
| OP497GPZ | 功能描述:IC OPAMP GP 500KHZ QUAD 14DIP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:MicroAmplifier™ 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:3.5 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:5pA 電壓 - 輸入偏移:1500µV 電流 - 電源:220µA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 36 V，±2.25 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:剪切帶 (CT) 其它名稱:296-29363-1 |
| OP497GPZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Picoampere Input Current Quad Operational Amplifier |
| OP497GS | 功能描述:IC OPAMP GP 500KHZ QUAD 16SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:Excalibur™ 放大器類型:J-FET 電路數:1 輸出類型:- 轉換速率:45 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:20pA 電壓 - 輸入偏移:490µV 電流 - 電源:1.7mA 電流 - 輸出 / 通道:48mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。