- 您現在的位置：買賣IC網 > Datasheet目錄55 > OPR5011 (TT Electronics/Optek Technology)COMPARATOR OPTICAL 3 CHAN SMD Datasheet資料下載
參數資料
| 型號： | OPR5011 |
| 廠商： | TT Electronics/Optek Technology |
| 文件頁數： | 3/3頁 |
| 文件大小： | 130K |
| 描述： | COMPARATOR OPTICAL 3 CHAN SMD |
| 標準包裝： | 1 |
| 系列： | * |
| 傳感器類型： | * |
| 輸出類型： | * |
OPTEK Technology Inc. 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Issue D 06/2012
Page 3 of 3
Optical Comparator Array
OPR5011
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Absolute Maximum Ratings (T
A
= 25?C unless otherwise noted)
Storage and Operating Temperature
-40?C to +100?C
Supply Voltage
24 V
Solder reflow time within 5癈 of peak temperature is 20 to 40 seconds
(1)
250?C
Power Dissipation
500 mW
Output Current
14 mA
Output Voltage
24 V
Electrical Characteristics (T
A
= 25?C unless otherwise noted)
SYMBOL
PARAMETER
MIN TYP MAX UNITS
TEST CONDITIONS
I
CC
Supply Current
-
9
20
mA
V
CC
= 24 V
V
OL
Low Level Output Voltage
(2)
-
0.3
0.4
V
I
OL
= 14 mA, V
CC
= 4.5 V
I
OH
High Level Output Current
(3)
-
0.1
1
礎
V
CC
= V
O
= 20 V
OPT-HYS Optical Hysteresis
(4)(7)
-
40
-
%
V
CC
= 5 V, I
OL
= 1 mA
OPT-OFF Optical Offset
(4)(7)
-40
10
+40
%
V
CC
= 5 V, I
OL
= 1 mA
f
max
Frequency Response
(5)
-
1
-
MHz
t
lh
Output Rise Time
(6)
-
1
-
祍
t
hl
Output Fall Time
(6)
-
300
-
ns
V
CC
= 5 V
Notes:
(1) Solder time less than 5 seconds at temperature extreme.
(2) Pin (+) = 100.0 nW and Pin (-) = 1.0 礧 .
(3) Pin (+) = 1.0 礧 and Pin (-) = 100.0 nW.
(4) Pin (-) is held at 1.0 礧 while Pin (+) is ramped from 0.5 礧 to 1.5 礧 and back to 0.5 礧.
(5) Pin (+) is modulated from 1.0 礧 to 2.0 礧. Pin (-) is modulated from 1.0 礧 to 2.0 礧 with phase shifted 180?with respect to
Pin (+). Use 100 k& trimpot to set the output signal to 50% duty cycle for maximum operating frequency.
(6) Measured between 10% and 90% points.
(7) Optical Hysteresis and Optical Offset are found by placing 1.0 礧 of light on the inverting photodiode and ramping the light
intensity of the non-inverting input from 0.5 礧 up to 1.5 礧 and back down. This will produce two trigger points an upper trigger
point and lower trigger point. These points are used to calculate the optical hysteresis and offset.
These are defined as:
% Optical Hysteresis = 100 x (P rise - P fall)
P in (-)
% Optical Offset = 100 x (P average - P (-))
P in (-)
Where:
P in (-)
= Light level incident upon the - photodiode on the IC chip (Pin) (-) = 1.0 礧).
P rise = Value of light power level incident upon the + photodiode that his required to switch the digital output when the
light level is an increasing level (rising edge).
P fall = Value of light power level incident upon the + photodiode that is required to switch the digital output when the light
level is decreasing level (falling edge).
P average = (P rise + P fall)
2
相關PDF資料 |
PDF描述 |
|---|---|
| P522304 | CELL ANTENNA 5-BAND 35X9X3.2MM |
| P522306 | RF ANT PRESTTA PENTA-BAND U.FL |
| P522309 | RF ANT PRESTTA PENTA U.FL |
| PA.11 | ANTENNA 2.4GHZ SMT |
| PA.12 | RF ANT 2.4GHZ SMT PIFA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OPR5011_07 | 制造商:OPTEK 制造商全稱:OPTEK 功能描述:Optical Comparator Array |
| OPR5011T | 功能描述:Photodiode 1μs 制造商:tt electronics/optek technology 系列:- 包裝:* 零件狀態:在售 波長:- 顏色 - 增強:- 頻譜范圍:- 二極管類型:- 不同 nm 時的響應度:- 響應時間:1μs 電壓 - DC 反向（Vr）（最大值）:- 電流 - 暗（典型值）:- 有效面積:0.50mm2（x6） 視角:- 工作溫度:-40°C ~ 100°C 安裝類型:表面貼裝 封裝/外殼:- 標準包裝:1 |
| OPR5013 | 制造商:OPTEK 制造商全稱:OPTEK 功能描述:SMD Multi Element Phototransistor |
| OPR5013L | 制造商:OPTEK 制造商全稱:OPTEK 功能描述:SMD Multi Ele ment LED Ar ray |
| OPR5200 | 功能描述:紅外發射源 Infrared 890nm RoHS:否 制造商:Fairchild Semiconductor 波長:880 nm 射束角:+/- 25 輻射強度: 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:Side Looker 封裝:Bulk |
發布緊急采購，3分鐘左右您將得到回復。