- 您現在的位置：買賣IC網 > PDF目錄382368 > P82C150AFT (NXP SEMICONDUCTORS) CAN Serial Linked I/O device SLIO with digital and analog port functions PDF資料下載
參數資料
| 型號： | P82C150AFT |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | CAN Serial Linked I/O device SLIO with digital and analog port functions |
| 中文描述： | 1 CHANNEL(S), 125K bps, LOCAL AREA NETWORK CONTROLLER, PDSO28 |
| 封裝： | 7.50 MM, PLASTIC, SO-28 |
| 文件頁數： | 33/36頁 |
| 文件大?。?/td> | 209K |
| 代理商： | P82C150AFT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁
1996 Jun 19
33
Philips Semiconductors
Preliminary specification
CAN Serial Linked I/O device (SLIO) with
digital and analog port functions
P82C150
13 SOLDERING
13.1
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
cases reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook” (order code 9398 652 90011).
13.2
Reflow soldering
Reflow soldering techniques are suitable for all SO
packages.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from 215 to
250
°
C.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45
°
C.
13.3
Wave soldering
Wave soldering techniques can be used for all SO
packages if the following conditions are observed:
A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave) soldering
technique should be used.
The longitudinal axis of the package footprint must be
parallel to the solder flow.
The package footprint must incorporate solder thieves at
the downstream end.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Maximum permissible solder temperature is 260
°
C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150
°
C within
6 seconds. Typical dwell time is 4 seconds at 250
°
C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
13.4
Repairing soldered joints
Fix the component by first soldering two diagonally-
opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300
°
C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds at between 270 and
320
°
C
相關PDF資料 |
PDF描述 |
|---|---|
| P82C150AHT | 22 PIN R/A MALE PRESSFIT ATCA ZONE 1 CON |
| P82C605 | System Controller |
| P82C606 | System Controller |
| P82C607 | Peripheral IC |
| P82C611 | Micro Channel Bus Interface/Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P82C150AHT | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:CAN Serial Linked I/O device SLIO with digital and analog port functions |
| P82C201-10 | 制造商:CHIPS 功能描述: 制造商:CHIP 功能描述:SYSTEM CONTROLLER, 84 Pin, PLCC 制造商:CHIPS 功能描述:SYSTEM CONTROLLER, 84 Pin, PLCC |
| P82C201-10 TS89 | 制造商:TOS 功能描述:82C201-10 |
| P82C201-10-7014-0093 | 制造商:CHIPS 功能描述: |
| P82C20110TS89 | 制造商:TOS 功能描述:82C201-10 |
發布緊急采購，3分鐘左右您將得到回復。