- 您現在的位置：買賣IC網 > PDF目錄382378 > PCA8516 (NXP Semiconductors N.V.) Stand-alone OSD PDF資料下載
參數資料
| 型號： | PCA8516 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Stand-alone OSD |
| 中文描述： | 單機OSD |
| 文件頁數： | 14/64頁 |
| 文件大小： | 403K |
| 代理商： | PCA8516 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
1995 Mar 30
14
Philips Semiconductors
Preliminary specification
Stand-alone OSD
PCA8516
8.2
Loading character data into display RAM
Three registers are used to address and load data into the
display RAM. These registers are described below.
8.2.1
DCR A
DDRESS
R
EGISTER
(DCRAR)
Table 5
DCR Address Register
This register holds the address of the location in display
RAM into which data is to be written. Command 3 loads
the High nibble of the address into this register;
Command 4 loads the Low nibble of the address.
8.2.2
DCR A
TTRIBUTE
R
EGISTER
(DCRTR)
Table 6
DCR Attribute Register
The Attribute Register is loaded with character font
attribute data using Command 2. The data will be loaded
into bits <4-0> of the location in RAM addressed by the
contents of DCRAR. Bits 7 to 5 are not used and are
reserved.
8.2.3
DCR C
HARACTER
R
EGISTER
(DCRCR)
Table 7
DCR Character Register
This register holds the character font data loaded by
Command 1. The data will be loaded into bits <12-5> of
the location in RAM addressed by the contents of DCRAR.
7
6
5
4
3
2
1
0
A7
A6
A5
A4
A3
A2
A1
A0
7
6
5
4
3
2
1
0
T4
T3
T2
T1
T0
7
6
5
4
3
2
1
0
C7
C6
C5
C4
C3
C2
C1
C0
8.3
Writing character data to display RAM
The procedure for writing character data to the display
RAM is as follows:
1.
Select the start address in display RAM. The start
address can take any value between 0 and 255.
Command 3 is used to load the High nibble of the start
address. Command 4 is used to load the Low nibble of
the start address. The start address is stored in
DCRAR.
2.
Load the character attributes into DCRTR using
Command 2. The actual attribute selected is
dependent upon whether the Character Font Code,
Carriage Return Code or Space Code has been
selected by Command 1 (see Section 8.1).
If the attributes of a series of displayed characters are
the same, the contents of this register need not be
updated.
3.
Load the Character Font data into DCTCR using
Command 1 or Command 5. Either of these
commands signal that a complete command byte is
available and the data held in registers DCRTR and
DCRCR is loaded into the RAM location pointed to by
the address stored in DCRAR. The address held in
DCRAR is then incremented by ‘1’ pointing to the next
RAM location in anticipation of the next operation.
A description of all the Commands is given in Chapter 9.
相關PDF資料 |
PDF描述 |
|---|---|
| PCA8516P | Stand-alone OSD |
| PCA8521 | Infrared remote control transmitter RC5 |
| PCA8521BP | Infrared remote control transmitter RC5 |
| PCA8521BT | Infrared remote control transmitter RC5 |
| PCA8521FP | Infrared remote control transmitter RC5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA85162 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal LCD driver for low multiplex rates |
| PCA85162T/Q900/1,1 | 功能描述:LCD 驅動器 32 SGMT 4800Hz RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| PCA85162T/Q900/1,118 | 制造商:NXP Semiconductors 功能描述:Cut Tape |
| PCA85162T/Q900/1,1-CUT TAPE | 制造商:NXP 功能描述:PCA85162 Series 5.5 V Low Multiplex Rates Universal LCD Driver - TSSOP-48 |
| PCA85162T-Q900-1 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal LCD driver for low multiplex rates |
發布緊急采購，3分鐘左右您將得到回復。