- 您現在的位置：買賣IC網 > PDF目錄382378 > PCA8516P (NXP SEMICONDUCTORS) Stand-alone OSD PDF資料下載
參數資料
| 型號： | PCA8516P |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 畫面疊加 |
| 英文描述： | Stand-alone OSD |
| 中文描述： | ON-SCREEN DISPLAY IC, PDIP24 |
| 封裝： | 0.400 INCH, PLASTIC, SDIP-24 |
| 文件頁數： | 19/64頁 |
| 文件大?。?/td> | 403K |
| 代理商： | PCA8516P |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
1995 Mar 30
19
Philips Semiconductors
Preliminary specification
Stand-alone OSD
PCA8516
9.4
Command 3
Table 19
Command 3 format
Command 3 loads the DCR Address Register with the
4 MSBs of the RAM address to which data will be written.
9.5
Command 4
Table 20
Command 4 format
Command 4 loads the DCR Address Register with the
4 LSBs of the RAM address to which data will be written.
9.6
Command 5
Table 21
Command 5 format
Command 5 is used to load character data into the DCR
Character Register. The data will specify either a
Character Font Code, the Test Code, the Carriage Return
Code or the Space Code. These codes are explained in
detail in Section 8.1.
9.7
Command 6
Table 22
Command 6 format
Command 6 loads the programmable 6-bit counter of the
OSD clock oscillator. The output frequency (f
OSD
) is a
function of the decimal value of the 6-bits loaded in by
Command 6; see Chapter 11.
BS1
BS0
7
6
5
4
3
2
1
0
0
0
0
0
1
1
A7
A6
A5
A4
BS1
BS0
7
6
5
4
3
2
1
0
0
0
0
0
1
1
A3
A2
A1
A0
BS1
BS0
7
6
5
4
3
2
1
0
1
0
1
C6
C5
C4
C3
C2
C1
C0
BS1
BS0
7
6
5
4
3
2
1
0
0
1
0
0
D5
D4
D3
D2
D1
D0
9.8
Command 7
Table 23
Command 7 format
This command loads Control Register 1 with data that
selects the scanning mode, the output polarity of signals
FB, ACM, R, G, B and I, and also enables/disables the
OSD clock.
With reference to the scanning modes: 1V/2V is the
conventional NTSC or PAL scanning mode; 1V/2H is the
Line Progress Scan used for the IDTV in NTSC and 2V/2H
is for the PAL system and is known as 50 Hz to 100 Hz
scan conversion.
Table 24
Selection of Scanning Mode
Table 25
Selection of output polarity (see Fig.13)
Table 26
OSD clock control
BS1
BS0
7
6
5
4
3
2
1
0
0
1
0
1
0
0
M1
M0
Bp
EN
M1
M0
SCAN MODE
0
0
1V/1H; NTSC 525LPF/60 Hz or
PAL 625LPF/50 Hz; see Fig.11. This is
the default setting.
reserved
1V/2H; NTSC 1050LPF/60 Hz; see
Fig.11.
2V/2H; PAL 1250LPF/100 Hz; see
Fig.12.
0
1
1
0
1
1
Bp
OUTPUT POLARITY (FB, ACM, R, G, B, I)
0
1
active LOW
active HIGH (the default setting)
EN
OSD CLOCK
0
1
disabled (the default setting)
enabled
相關PDF資料 |
PDF描述 |
|---|---|
| PCA8521 | Infrared remote control transmitter RC5 |
| PCA8521BP | Infrared remote control transmitter RC5 |
| PCA8521BT | Infrared remote control transmitter RC5 |
| PCA8521FP | Infrared remote control transmitter RC5 |
| PCA8521FT | Infrared remote control transmitter RC5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA8516T | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Stand-alone OSD |
| PCA85176 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal LCD driver for low multiplex rates |
| PCA85176H/Q900/1,5 | 功能描述:LCD 驅動器 40 SGMT 4800Hz RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| PCA85176H/Q900/1,518 | 制造商:NXP Semiconductors 功能描述:Cut Tape |
| PCA85176H-Q900 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal LCD driver for low multiplex rates |
發布緊急采購，3分鐘左右您將得到回復。