- 您現在的位置：買賣IC網 > PDF目錄382378 > PCA8581C (NXP Semiconductors N.V.) 128 x 8-bit EEPROM with I2C-bus interface PDF資料下載
參數資料
| 型號： | PCA8581C |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | DRAM |
| 英文描述： | 128 x 8-bit EEPROM with I2C-bus interface |
| 中文描述： | 128 × 8位EEPROM帶I2C總線接口 |
| 文件頁數： | 16/20頁 |
| 文件大小： | 107K |
| 代理商： | PCA8581C |
1997 Apr 02
16
Philips Semiconductors
Product specification
128
×
8-bit EEPROM with I
2
C-bus
interface
PCA8581; PCA8581C
14 SOLDERING
14.1
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook”(order code 9398 652 90011).
14.2
DIP
14.2.1
S
OLDERING BY DIPPING OR BY WAVE
The maximum permissible temperature of the solder is
260
°
C; solder at this temperature must not be in contact
with the joint for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (T
stg max
). If the
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
14.2.2
R
EPAIRING SOLDERED JOINTS
Apply a low voltage soldering iron (less than 24 V) to the
lead(s) of the package, below the seating plane or not
more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300
°
C it may remain in
contact for up to 10 seconds. If the bit temperature is
between 300 and 400
°
C, contact may be up to 5 seconds.
14.3
SO
14.3.1
R
EFLOW SOLDERING
Reflow soldering techniques are suitable for all SO
packages.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from
215 to 250
°
C.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45
°
C.
14.3.2
W
AVE SOLDERING
Wave soldering techniques can be used for all SO
packages if the following conditions are observed:
A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave) soldering
technique should be used.
The longitudinal axis of the package footprint must be
parallel to the solder flow.
The package footprint must incorporate solder thieves at
the downstream end.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Maximum permissible solder temperature is 260
°
C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150
°
C within
6 seconds. Typical dwell time is 4 seconds at 250
°
C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
14.3.3
R
EPAIRING SOLDERED JOINTS
Fix the component by first soldering two diagonally-
opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300
°
C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320
°
C.
相關PDF資料 |
PDF描述 |
|---|---|
| PCA8581CP | 128 x 8-bit EEPROM with I2C-bus interface |
| PCA8581CT | 128 x 8-bit EEPROM with I2C-bus interface |
| PCA8581P | 128 x 8-bit EEPROM with I2C-bus interface |
| PCA8581T | 128 x 8-bit EEPROM with I2C-bus interface |
| PCA8581 | 128 x 8-bit EEPROM with I2C-bus interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA8581CP | 制造商:NXP Semiconductors 功能描述:128 X 8 EEPROM 3V, PDIP8 |
| PCA8581CT | 制造商:NXP Semiconductors 功能描述: |
| PCA8581CT/6,112 | 功能描述:電可擦除可編程只讀存儲器 128X8 電可擦除可編程只讀存儲器 I2C-BUS SO-8 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| PCA8581CT/6,118 | 功能描述:電可擦除可編程只讀存儲器 128X8 電可擦除可編程只讀存儲器 I2C-BUS SO-8 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| PCA8581CTD-T | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
發布緊急采購，3分鐘左右您將得到回復。