- 您現在的位置：買賣IC網 > PDF目錄382379 > PCA9548 (NXP Semiconductors N.V.) 8-channel I2C switch with reset PDF資料下載
參數資料
| 型號： | PCA9548 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 8-channel I2C switch with reset |
| 中文描述： | 8通道的I2C與復位開關 |
| 文件頁數： | 7/16頁 |
| 文件大小： | 125K |
| 代理商： | PCA9548 |
Philips Semiconductors
Product data sheet
PCA9548
8-channel I
2
C switch with reset
2004 Sep 30
7
CHARACTERISTICS OF THE I
2
C-BUS
The I
2
C-bus is for 2-way, 2-line communication between different ICs
or modules. The two lines are a serial data line (SDA) and a serial
clock line (SCL). Both lines must be connected to a positive supply
via a pull-up resistor when connected to the output stages of a device.
Data transfer may be initiated only when the bus is not busy.
Bit transfer
One data bit is transferred during each clock pulse. The data on the
SDA line must remain stable during the HIGH period of the clock
pulse as changes in the data line at this time will be interpreted as
control signals (see Figure 6).
SDA
SCL
SW00363
data line
stable;
data valid
change
of data
allowed
Figure 6. Bit transfer
Start and stop conditions
Both data and clock lines remain HIGH when the bus is not busy. A
HIGH-to-LOW transition of the data line, while the clock is HIGH is
defined as the start condition (S). A LOW-to-HIGH transition of the
data line while the clock is HIGH is defined as the stop condition (P)
(see Figure 7).
System configuration
A device generating a message is a ‘transmitter’, a device receiving
is the ‘receiver’. The device that controls the message is the
‘master’ and the devices which are controlled by the master are the
‘slaves’ (see Figure 8).
SDA
SCL
SW00365
S
P
SDA
SCL
START condition
STOP condition
Figure 7. Definition of start and stop conditions
MASTER
TRANSMITTER/
RECEIVER
SLAVE
RECEIVER
SLAVE
TRANSMITTER/
RECEIVER
MASTER
TRANSMITTER
MASTER
TRANSMITTER/
RECEIVER
SDA
SCL
SW00366
I
2
C
MULTIPLEXER
SLAVE
Figure 8. System configuration
相關PDF資料 |
PDF描述 |
|---|---|
| PCA9548D | 8-channel I2C switch with reset |
| PCA9548PW | 8-channel I2C switch with reset |
| PCA9550 | 2-bit I2C LED driver with programmable blink rates |
| PCA9551 | 8-bit I2C LED driver with programmable blink rates |
| PCA9552 | GT 10C 10#16 SKT RECP BOX RM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9548A | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-channel I2C-bus switch with reset |
| PCA9548ABS | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-channel I2C-bus switch with reset |
| PCA9548ABS,118 | 功能描述:多路器開關 IC 4CH I2C SWTCH W/REST RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| PCA9548ABS,118-CUT TAPE | 制造商:NXP 功能描述:PCA9548 Series 8-Channel I2C-Bus Translating Switch w/ Reset - HVQFN - 24 |
| PCA9548ABSHP | 功能描述:多路器開關 IC RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
發布緊急采購，3分鐘左右您將得到回復。