- 您現在的位置：買賣IC網 > PDF目錄382379 > PCA9560D (NXP SEMICONDUCTORS) The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each PDF資料下載
參數資料
| 型號： | PCA9560D |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 通用總線功能 |
| 英文描述： | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| 中文描述： | 9560 SERIES, 3 LINE TO 1 LINE MULTIPLEXER, TRUE OUTPUT, PDSO20 |
| 封裝： | 7.50 MM, PLASTIC, MS-013, SOT-163-1, SOP-20 |
| 文件頁數： | 8/17頁 |
| 文件大小： | 111K |
| 代理商： | PCA9560D |
Philips Semiconductors
Product data
PCA9560
Dual 5-bit multiplexed 1-bit latched
I
2
C EEPROM DIP switch
2003 Jun 27
8
Acknowledge
The number of data bytes transferred between the start and the stop conditions from transmitter to receiver is not limited. Each byte of eight bits
is followed by one acknowledge bit. The acknowledge bit is a HIGH-level put on the bus by the transmitter whereas the master generates an
extra acknowledge related clock pulse.
A slave receiver which is addressed must generate an acknowledge after the reception of each byte. Also a master must generate an
acknowledge after the reception of each byte that has been clocked out of the slave transmitter. The device that acknowledges has to pull down
the SDA line during the acknowledge clock pulse, so that the SDA line is stable LOW during the HIGH period of the acknowledge related clock
pulse, set-up and hold times must be taken into account.
A receiver must signal an end of data to the transmitter by not generating an acknowledge on the last byte that has been clocked out of the
slave. In this event, the transmitter must leave the data line HIGH to enable the master to generate a stop condition.
DATA OUTPUT
BY TRANSMITTER
SCL FROM
MASTER
SW00368
DATA OUTPUT
BY RECEIVER
1
2
8
9
S
START condition
clock pulse for
acknowledgement
acknowledge
not acknowledge
Figure 8. Acknowledgement on the I
2
C-bus
相關PDF資料 |
PDF描述 |
|---|---|
| PCB2032V | EEPROM |
| PCB2320DP | ISDN Line Interface |
| PCB2325DP | ISDN Line Interface |
| PCB2391A | ISDN， Other/Special/Miscellaneous |
| PCB2421TD-T | I2C Serial EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9560D,112 | 功能描述:多路器開關 IC DUAL5BTMUX 1B LATCH RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| PCA9560D,118 | 功能描述:多路器開關 IC DUAL5BTMUX 1B LATCH RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| PCA9560D-T | 功能描述:電可擦除可編程只讀存儲器 DUAL5BTMUX 1B LATCH I2C EPROM RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| PCA9560PW | 功能描述:電可擦除可編程只讀存儲器 DUAL5BTMUX 1B LATCH I2C EPROM RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| PCA9560PW,112 | 功能描述:多路器開關 IC DUAL5BTMUX 1B LATCH RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
發布緊急采購，3分鐘左右您將得到回復。