- 您現在的位置：買賣IC網 > PDF目錄382380 > PCD5003H (NXP SEMICONDUCTORS) Advanced POCSAG Paging Decoder PDF資料下載
參數資料
| 型號： | PCD5003H |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 尋呼電路 |
| 英文描述： | Advanced POCSAG Paging Decoder |
| 中文描述： | TELECOM, PAGING DECODER, PQFP32 |
| 封裝： | 7 X 7 MM, 1.40 MM HEIGHT, PLASTIC, SOT-358-1, LQFP-32 |
| 文件頁數： | 10/44頁 |
| 文件大小： | 187K |
| 代理商： | PCD5003H |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
1997 Jun 24
10
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
PCD5003
This is done for a period of up to 15 batches, allowing
recovery of synchronization from long fades in the radio
signal. Detection of preamble switches to
‘preamble receive’ mode, while sync word detection
switches to ‘data receive’ mode. When neither is found
within a period of 15 batches, the radio signal is
considered lost and ‘carrier off’ mode is entered.
The purpose of
carrier off
mode is to detect a valid radio
transmission and synchronize to it quickly and efficiently.
Because transmissions may start at random, the decoder
enables the receiver for 1 codeword in every
18 codewords looking for preamble or sync word. By using
a buffer containing 32 bits (n bits from the current scan,
32
n from the previous scan) effectively every batch bit
position can be tested within a continuous transmission of
at least 18 batches. Detection of preamble switches to
‘preamble receive’ mode, while sync word detection
switches to ‘data receive’ mode.
7.13
Call termination
Call reception is terminated:
Upon reception of any address codeword (including Idle
codeword) requiring no more than single bit error
correction
In ‘data fail’ mode, when a sync word is not found at the
expected batch position
When a forced call termination command is received
from an external controller.
The last method permits an external controller to stop call
reception depending on the number and type of errors
which occurred in a call. After a forced call termination the
decoder will enter ‘data fail’ mode.
The type of error correction as well as the call termination
conditions are indicated by status bits in the message data
output.
Following call termination, transfer of the data received
since the previous sync word period is initiated by means
of an interrupt to the external controller.
7.14
Call data output format
POCSAG call information is stored in the decoder SRAM
in blocks of 3 bytes per codeword. Each stored call
consists of a call header, followed by message data blocks
and concluded by a call terminator. In the event of
concatenated messages the call terminator is replaced
with the call header of the next message. An alert-only call
only has a call header and a call terminator.
The formats of a call header, a message data block and a
call terminator are shown in Tables 4, 6 and 8.
A
Call Header
contains information on the last sync word
received, the RIC which began call reception and the type
of error correction performed on the address codeword.
A
Message Data
block contains the data bits from a
message codeword plus the type of error correction
performed. No deformatting is done on the data bits:
numeric data appear as 4-bit groups per digit,
alphanumeric data have a 7-bit ASCII representation.
The
Call Terminator
contains information on the last sync
word received, information on the way the call was
terminated (forced call termination command, loss of sync
word in ‘data fail’ mode) and the type of error correction
performed on the terminating codeword.
7.15
Sync word indication
The sync word recognized by the PCD5003 is shown in the
call header (bits S3 to S1). The decimal value represents
the identifier number in the EEPROM of the UPSW in
question. A value of 7 indicates the standard POCSAG
sync word.
7.16
Error type indication
Table 10 shows how the different types of detected errors
are encoded in the call data output format.
A message codeword containing more than a single bit
error (bit E3 = 1) may appear as an address codeword
(bit M1 = 0) after error correction. In this event the
codeword is processed as message data and does not
cause call termination.
7.17
Data transfer
Data transfer is initiated either during sync word periods or
as soon as the receiver is disabled after call termination.
If the SRAM buffer is full, data transfer is initiated
immediately during the next codeword.
When the PCD5003 is ready to transfer received call data
an external interrupt will be generated via output INT.
Any message data can be read by accessing the RAM
output register via the I
2
C-bus interface. Bytes will be
output starting from the position indicated by the RAM read
pointer.
相關PDF資料 |
PDF描述 |
|---|---|
| PCD5008 | FLEX Pager Decoder |
| PCD5008H | FLEX Pager Decoder |
| PCD5013 | FLEX roaming decoder II |
| PCD5013H | FLEX roaming decoder II |
| PCD5032 | ADPCM CODEC for digital cordless telephones |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCD5003HB-T | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication Decoder |
| PCD5003U/10 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Advanced POCSAG Paging Decoder |
| PCD5008 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:FLEX Pager Decoder |
| PCD5008H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:FLEX Pager Decoder |
| PCD5008HBD-T | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication Decoder |
發布緊急采購，3分鐘左右您將得到回復。