- 您現在的位置：買賣IC網 > PDF目錄382380 > PCD5043 (NXP Semiconductors N.V.) DECT burst mode controller PDF資料下載
參數資料
| 型號： | PCD5043 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | DECT burst mode controller |
| 中文描述： | 無繩突發模式控制器 |
| 文件頁數： | 14/24頁 |
| 文件大小： | 109K |
| 代理商： | PCD5043 |
1996 Oct 31
14
Philips Semiconductors
Objective specification
DECT burst mode controller
PCD5043
The ‘DPLL_sync’ indication should only be used, when
‘SlotSync’ is active. It indicates that the last 4 bits of the
pre-amble field (the training sequence) are received
correctly, and thus indicates that the DPLL was in lock
(synchronized) in time. If the ‘SlotSync’ is active, and the
‘DPLL_sync’ is not, then a sliding interferer might have
been detected.
If ‘SlotSync’ is not detected, effectively no data is received
in that slot. This implies a ‘fast mute’ because speech data
received in the previous frame is not destroyed.
6.5.9
C
IPHERING MACHINE
The description of the cipher machine is subject to
confidentiality. The specification of its algorithms are
delivered by ETSI under the terms of a Non-Disclosure
Agreement.
The cipher machine is under control of the TBC, which is
implemented in the PCC. The cipher machine generates
2 fields of ciphering bits:
A_cipher (40 bits) for A-field messages (ciphers tail
only)
B_cipher (320 bits) for speech in B-field.
The transmitted ciphered bits are then:
A_ciphered: = A XOR A_cipher
B_ciphered: = B XOR B_cipher.
On reception by the peer end point, deciphering consists
of the same operation thanks to the synchronous
generation of A_cipher and B_cipher.
The cipher machine is time-multiplexed on a slot basis.
Initially, the Initialisation Vector (IV) and the key must be
loaded into the cipher machine. Transfer of the IV and key
from the common data area to the cipher machine is done
automatically by the cipher machine. The contents of the
memory space where IV and key are found, are the
Fig.10 Cipher machine and its sources.
handbook, halfpage
MBH714
KEY
64 BITS
CIPHER
MACHINE
A_cipher
(40 bits)
B_cipher
(320 bits)
KEY
64 BITS
responsibility of the PCC, and the external
microprocessor.
6.6
Microcontroller Interface
6.6.1
F
UNCTION OF THE MICROCONTROLLER INTERFACE
The microcontroller Interface will provide the following
services.
Direct interface to processors which have an
INTEL-8051 compatible interface
General interface to processors that can handle ‘wait
states’ e.g. 68000-family; in this case glue logic is
required
Processor clock signal of which the frequency is
programmable in order to adjust instantaneously
processor performance to processor work load
A programmable interrupt register
A watchdog timer with time-out periods of
1.25 or 82 seconds, depending on the programming.
The microcontroller can address the PCD5043 as any
other RAM memory connected to the microcontroller bus.
By writing the ‘Interface-Mode Register’, the
microcontroller can select the interface mode and its own
clock frequency.
6.6.2
M
ICROCONTROLLER INTERRUPTS
The function of microcontroller Interrupts is to make
optimal use of the microcontroller’s processing power, and
to achieve optimal cooperation between time-critical tasks
and less time-critical tasks both executed in software.
Three registers are available to handle interrupts. These
are:
Interrupt Event Register
Interrupt Enable Register
Interrupt Reset Register.
These registers are to be regarded together.
Corresponding bits in these registers relate to one and the
same event. Bits in the Interrupt Event Register are set by
the PCC and are to be reset by the external processor by
writing ‘1’s in the corresponding bits in the Interrupt Reset
Register. The mask in the Interrupt Enable Register
enables the interrupt if corresponding events do occur.
相關PDF資料 |
PDF描述 |
|---|---|
| PCD5043H | DECT burst mode controller |
| PCD5091HZ | DECT baseband controller |
| PCD5091 | DECT baseband controller |
| PCD5091H | DECT baseband controller |
| PCD5092 | DECT baseband controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCD5043H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:DECT burst mode controller |
| PCD5071 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MODEM |
| PCD5090 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:DECT baseband controllers |
| PCD5090H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:DECT baseband controllers |
| PCD5090H232F1 | 制造商:PHILIPS 功能描述:* |
發布緊急采購，3分鐘左右您將得到回復。