欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: PSD302R-90JM
廠商: 意法半導體
英文描述: Low Cost Field Programmable Microcontroller Peripherals
中文描述: 低成本現場可編程微控制器外圍設備
文件頁數: 25/85頁
文件大小: 691K
代理商: PSD302R-90JM
PSD3XX Famly
22
12.0
Control Signals
Consult your MCU data sheet to determine which control signals your MCU generates, and
how they operate. This section is intended to show which control signals should be
connected to what pins on the PSD3XX. You will then use PSDsoft to configure the
PSD3XX, based on the combination of control signals that your MCU outputs, for example
RD, WR, and PSEN.
The PSD3XX is compatible with the following control signals:
ALE or AS (polarity is programmable)
WR or R/W
RD/E or RD/E/DS (DS for non-3X1 devices only)
BHE or PSEN
A19/CSI
RESET (polarity is programmable except on low voltage versions with the V suffix).
12.1 ALE or AS
Connect the ALE or AS signal from your MCU to this pin where applicable, and program
the polarity using PSDsoft. The trailing edge (when the signal goes inactive) of ALE or AS
latches the address on any pins that have an address input. If you are using a
non-multiplexed-bus MCU that does not output an ALE or AS signal, this pin can be used
for a generic input to the PAD.
Note: if your data is multiplexed with address lines other
than A0-A7
, connect your address pins to AD0/A0-AD15/A15, and connect your data to
Port A (and Port B where applicable), and connect the ALE/AS signal to this pin.
12.2 WR or R/W
Your MCU should output a stand-alone write signal (WR) or a multiplexed read/write signal
(R/W). In either case, the signal should be connected to this pin.
12.3 RD/E/DS (DS option not available on 3X1 devices)
Your MCU should output any one of RD, E (clock), or DS. In any case, connect the
appropriate signal to this pin.
12.4 BHE or PSEN
J
If your MCU does not output either of these signals, tie this pin to Vcc
(through a series resistor), and skip to the next signal.
J
If you use an 8-bit 8031 compatible MCU that outputs a separate signal when
accessing program space, such as PSEN, connect it to this pin. You would then use
PSDsoft to configure the EPROM in the PSD3XX to respond to PSEN only or PSEN
and RD. If you have an 8031 compatible MCU, refer to the “Program/Data Space and
the 8031” section for further information.
J
If you are using a 16-bit MCU, connect the BHE (or similar signal) output to this pin.
BHE enables accessing of the upper byte of the data bus. See Table 6 for information
on how this signal is used in conjunction with the A0 address line.
BHE
A
0
0
1
0
1
Operation
0
0
1
1
Whole Word
Upper Byte From/To Odd Address
Lower Byte From/To Even Address
None
Table 6. Truth Table for BHE and Address Bit A0 (16-bit MCUs only)
相關PDF資料
PDF描述
PSD302V-70JM Low Cost Field Programmable Microcontroller Peripherals
PSD312-15J Low Cost Field Programmable Microcontroller Peripherals
PSD312-15JI Low Cost Field Programmable Microcontroller Peripherals
PSD312-15JM Low Cost Field Programmable Microcontroller Peripherals
PSD312R-15J Low Cost Field Programmable Microcontroller Peripherals
相關代理商/技術參數
參數描述
PSD302R-A-15J 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
PSD302R-A-15JI 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
PSD302R-A-15JM 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
PSD302R-A-20J 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
PSD302R-A-20JI 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
主站蜘蛛池模板: 长宁县| 深水埗区| 太仆寺旗| 金平| 涟源市| 仪陇县| 阳东县| 铜陵市| 黄骅市| 海原县| 丰城市| 庆元县| 淳化县| 孟州市| 碌曲县| 阳山县| 竹北市| 大余县| 江孜县| 元氏县| 荥阳市| 冕宁县| 西城区| 临江市| 无锡市| 邓州市| 屏山县| 巫溪县| 和平县| 仙桃市| 德江县| 怀集县| 手机| 荔波县| 英山县| 深州市| 格尔木市| 确山县| 大厂| 新野县| 白河县|