欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: PSD303-B-70J
廠商: 意法半導體
英文描述: Low Cost Field Programmable Microcontroller Peripherals
中文描述: 低成本現場可編程微控制器外圍設備
文件頁數: 12/85頁
文件大小: 691K
代理商: PSD303-B-70J
PSD3XX Famly
9
Table 2.
PSD3XX Pin
Descriptions
(cont.)
Name
Type
Description
These pins make up Port B. These port pins are configurable, and
can have the following functions: (see Figure 6)
1. MCU I/O—in this mode, the direction of the pin is defined by its
direction bit, which resides in the direction register.
2. Chip select output—each of PB0-3 has four product terms
available per pin, while PB4-7 have 2 product terms each.
See Figure 4.
3. CMOS or open-drain.
4.
If your MCU is non-multiplexed, and the data bus width is
16 bits:
data bus input—connect your data bus (D8-D15) to these
pins. See Figure 3.
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
I/O
These pins make up Port C. These port pins are configurable, and
can have the following functions (see Figure 7):
1. PAD input—when configured as an input, a bit individually
becomes an address or a logic input, depending on your PSDsoft
design file. When declared as an address, the bit(s) can be latched
with ALE/AS.
2. PAD output—when configured as an output (i.e. there is an
equation written for it in your PSDsoft design file), there is one
product term available to it.
PC0
PC1
PC2
I/O
AD0/A0
AD1/A1
AD2/A2
AD3/A3
AD4/A4
AD5/A5
AD6/A6
AD7/A7
If your MCU is multiplexed:
These pins are the multiplexed, low-order address/data byte
(AD0-AD7). As inputs, address information is latched by the ALE/AS
signal and used internally by the PSD. The pins also serve as MCU
data bus inputs or outputs, depending on the MCU control signals
(RD, WR, etc.).
If your MCU is non-multiplexed:
These pins are the low-order address inputs (A0-A7)
I/O
AD8/A8
AD9/A9
AD10/A10
AD11/A11
AD12/A12
AD13/A13
AD14/A14
AD15/A15
If your MCU is multiplexed with a 16-bit data bus:
These pins are the multiplexed, high-order address/data byte
(AD8-AD15). As inputs, address information is latched by the
ALE/AS signal and used internally the PSD. The pins also
serve as MCU data bus inputs or outputs, depending on the MCU
control signals (RD, WR, etc.).
If your MCU is non-multiplexed or has a 8-bit data bus:
These pins are the high-order address inputs (A8-A15).
I/O
GND
P
Ground Pin
V
CC
P
Supply voltage input.
Legend:
The Type column abbreviations are: I = input only; I/O = input/output; P = power.
相關PDF資料
PDF描述
PSD303-B-70L Low Cost Field Programmable Microcontroller Peripherals
PSD303-B-70M Low Cost Field Programmable Microcontroller Peripherals
PSD303-B-70U Low Cost Field Programmable Microcontroller Peripherals
PSD303-B-90JI Low Cost Field Programmable Microcontroller Peripherals
PSD303-B-90LI Low Cost Field Programmable Microcontroller Peripherals
相關代理商/技術參數
參數描述
PSD303B-70J 功能描述:SPLD - 簡單可編程邏輯器件 5V 1M 70ns RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PSD303-B-70L 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
PSD303-B-70M 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
PSD303B-70M 功能描述:SPLD - 簡單可編程邏輯器件 5.0V 1M 70ns RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PSD303-B-70U 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
主站蜘蛛池模板: 乐亭县| 苍山县| 南岸区| 西丰县| 岫岩| 大化| 韩城市| 常德市| 法库县| 新宾| 凤台县| 濮阳县| 襄樊市| 和平区| 呈贡县| 福清市| 廉江市| 咸阳市| 新乡县| 屯昌县| 疏勒县| 方正县| 鹿邑县| 连州市| 诸城市| 苍南县| 钟祥市| 洪泽县| 双城市| 温泉县| 贡嘎县| 宣恩县| 京山县| 土默特左旗| 临湘市| 右玉县| 邵阳县| 张家口市| 北流市| 福鼎市| 乐都县|